2020年第4期共收录49篇
1. Spatial and Temporal Distribution Characteristics of Spring Maize Coefficients in Northeast China
Accession number: 20202008643916
Title of translation:
Authors: Li, Bo (1); Jing, Zhuran (1); Wei, Xinguang (1); Sun, Jun (1); Fu, Shining (1); Ge, Dong (1)
Author affiliation: (1) College of Water Conservancy, Shengyang Agricultural University, Shenyang; 110866, China
Corresponding author: Wei, Xinguang(weixg_wi@163.com)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 279-290
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Crop coefficient is an important parameter for estimating the change of water demand in crop growing season. Based on the meteorological and spring maize observations of 107 meteorological stations in the Northeast China from 1951 to 2018, the spring maize coefficients calculated by the model of crop coefficients were validated by using different crop coefficient correction formulas. The interannual variation trends and spatial distribution characteristics of crop coefficients during the whole period and each growth stage were analyzed by using spatial interpolation. The results showed that the single crop coefficient method considering the influence of wind speed and humidity had the best effect on the simulation of crop coefficient in the early stage of spring maize (R2=0.65). The coefficient of spring maize crops in the full growth period in the Northeast China was varied from 0.756 to 0.815. The spatial distribution of high-value areas was mainly distributed in the western part of Northeast China, and the low-value areas were mainly distributed in the northern part of Heilongjiang Province and the southeastern part of Liaoning Province. Crop coefficients at different fertility stages were the largest in the middle of fertility, followed by the rapid growth period, and the early and late stages of childbearing were generally small. In the past 70 years, the interannual variation of crop coefficient of spring maize in the Northeast China showed a significant downward trend (R2=0.38), and the tendency rate of crop coefficient reached -0.004/(10 a). In each reproductive period, the interannual changes of Kc showed a declining trend, Heilongjiang Province had the most obvious decline, followed by Jilin Province and eastern part of Inner Mongolia Autonomous region, changes of Liaoning Province were not obvious. The crop coefficient of most stations in Northeast China showed a decreasing trend, the decreasing trend and the significant decreasing trend accounted for 92.5% and 64.5% respectively. In different growth stages, the decline trend was the most obvious (46.7% in the rapid growth stage), and in the middle and late growth stage (41.1% and 34.6% respectively), the trend of change was not significant at the early stage of birth. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 47
Main heading: Spatial distribution
Controlled terms: Crops? - ?Cultivation? - ?Wind
Uncontrolled terms: Different growth stages? - ?Distribution characteristics? - ?Eastern part of inner mongolia? - ?Interannual variation? - ?Liaoning Province? - ?Meteorological station? - ?Spatial and temporal distribution? - ?Spatial interpolation
Classification code: 443.1 Atmospheric Properties? - ?821.3 Agricultural Methods? - ?821.4 Agricultural Products? - ?921 Mathematics
Numerical data indexing: Age 7.00e+01yr, Percentage 3.46e+01%, Percentage 4.11e+01%, Percentage 4.67e+01%, Percentage 6.45e+01%, Percentage 9.25e+01%
DOI: 10.6041/j.issn.1000-1298.2020.04.032
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
2. Preparation of Fe-Ce/Dolomite Catalyst and Its Catalytic Performance of Gasification Biomass
Accession number: 20202008644046
Title of translation: Fe-Ce/
Authors: Niu, Yonghong (1, 2); Liu, Kunkun (1); Cai, Yaoyao (1); Li, Yike (1); Wang, Wencai (2)
Author affiliation: (1) School of Energy and Environment, Inner Mongolia University of Science and Technology, Baotou; 014010, China; (2) Mining Research Institute, Inner Mongolia University of Science and Technology, Baotou; 014010, China
Corresponding author: Wang, Wencai(wencai99999@163.com)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 361-366
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Fe-Ce/dolomite catalyst was prepared by the impregnation method, and the catalyst was characterized by SEM and XRD. The high-temperature water vapor catalytic gasification test was carried out on a self-built fixed-bed gasification furnace test station, and the content of the auxiliary agent was studied. The effect of the gasification temperature and other factors on the gasification characteristics of the water vapor of pine rod and effect of number of times of catalyst on deposition of gas component and catalyst were researched. The experimental results showed that the auxiliary Fe and Ce can be well supported on the dolomite, and the catalyst gasification effect of the assistant content of 8% Fe-2% Ce was good. Fixed the catalytic temperature, and the catalyst was used for making the pine wood rod at different temperatures. In the steam gasification test, when the temperature was increased from 750 to 950, the gas production rate and hydrogen production rate were increased from 1.05 m3/kg and 31.67 g/kg at 750 to 1.56 m3/kg and 65.39 g/kg at 900, respectively. Compared with the gasification test without catalyst, the hydrogen production rate was increased by 0.15 m3/kg and 16.27 g/kg, and the hydrogen volume fraction was increased from 39.02% to 46.95%, respectively. The third gasification test of the catalyst was carried out at 800. The volume fraction of hydrogen was decreased from 40.34% in the first time to 38.97% in the second time and 34.95% in the third time. The amount of carbon deposition was increased from the first time of 21.55 mg/g to the third time of 31.61 mg/g. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 25
Main heading: Gasification
Controlled terms: Catalysts? - ?Deposition? - ?Gas industry? - ?Hydrogen production? - ?Volume fraction? - ?Water vapor
Uncontrolled terms: Catalytic gasification? - ?Catalytic performance? - ?Gasification characteristics? - ?Gasification furnace? - ?Gasification temperatures? - ?High-temperature water? - ?Hydrogen production rate? - ?Hydrogen volume fraction
Classification code: 522 Gas Fuels? - ?641.1 Thermodynamics? - ?802.3 Chemical Operations? - ?803 Chemical Agents and Basic Industrial Chemicals? - ?804 Chemical Products Generally
Numerical data indexing: Percentage 3.50e+01%, Percentage 3.90e+01%, Percentage 3.90e+01% to 4.70e+01%, Percentage 4.03e+01%, Specific_Volume 1.05e+00m3/kg, Specific_Volume 1.50e-01m3/kg, Specific_Volume 1.56e+00m3/kg
DOI: 10.6041/j.issn.1000-1298.2020.04.041
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
3. Reconstruction Method of Apple Tree Canopy Point-Leaf Model Based on 3D Point Clouds
Accession number: 20202008643859
Title of translation: -
Authors: Guo, Cailing (1, 2); Liu, Gang (1, 3)
Author affiliation: (1) Key Laboratory of Modern Precision Agriculture System Integration Research, Ministry of Education, China Agricultural University, Beijing; 100083, China; (2) Department of Electromechanical Engineering, Tangshan University, Tangshan; 063000, China; (3) Key Laboratory of Agricultural Information Acquisition Technology, Ministry of Agriculture and Rural Affairs, China Agricultural University, Beijing; 100083, China
Corresponding author: Liu, Gang(pac@cau.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 173-180
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: The fine structure inside the canopy of apple tree determines the light distribution and is one of the important factors affecting the quality and yield of apples. Aiming to rapidly generate apple tree canopy 3D reconstruction model to study the illumination distribution in it, a point-leaf model reconstruction method of apple canopy based on point cloud data was proposed. A Trimble TX8 was used as a data acquisition device to obtain 3D point clouds of the canopy in the flowering, leaf growth stage and stable growth stages of apple tree as the research object. Firstly, a leaf spatial location (LSL) extraction approach using density-based spatial clustering of applications with noise (DBSCAN) and layers K-means and median methods was proposed. In the LSL extraction progress, the DBSCAN clustering method based on adaptive parameters was used to extract the point cloud of single-leaf branches. And the same point cloud was sliced into layers, and the K-means and median method was used to fit the branch center line. And then, the Euclidean distance of each point between the single blade and the center line was determined, and the point with the smallest Euclidean distance (ELD) was the LSL point. Field experiments showed that the method proposed was suitable for LSL extraction during leaf growth and stable growth stage. Through comparative analysis between the automatical algorithm and artificial use of Realworks software extraction point showed that the average ELD between these two methods was 1.41 mm. Secondly, the whole apple tree canopy LSL was extracted by canopy voxelization, and the point model was constructed. Using the leaf templete to splice the LSL, the point-leaf model was formed. The light interception calculation (STAR value) in the VegeSTAR light model showed that the 3D reconstruction efficiency was improved greatly. Therefore, the point-leaf model reconstruction method was effective. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 34
Main heading: Three dimensional computer graphics
Controlled terms: 3D modeling? - ?Data acquisition? - ?Extraction? - ?Fruits? - ?Image reconstruction? - ?K-means clustering? - ?Trees (mathematics)
Uncontrolled terms: 3-D reconstruction model? - ?Adaptive parameters? - ?Comparative analysis? - ?Data-acquisition devices? - ?Density-based spatial clustering of applications with noise? - ?Illumination distribution? - ?Model reconstruction? - ?Reconstruction method
Classification code: 723.2 Data Processing and Image Processing? - ?802.3 Chemical Operations? - ?821.4 Agricultural Products? - ?921.4 Combinatorial Mathematics, Includes Graph Theory, Set Theory
Numerical data indexing: Size 1.41e-03m
DOI: 10.6041/j.issn.1000-1298.2020.04.020
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
4. Paddy Rice Planting Area Extraction in County-level Based on Spatiotemporal Data Fusion
Accession number: 20202008644285
Title of translation:
Authors: Niu, Haipeng (1, 2); Wang, Zhanqi (1); Xiao, Dongyang (1)
Author affiliation: (1) School of Surveying and Land Information Engineering, Henan Polytechnic University, Jiaozuo; 454000, China; (2) Institute of Ecological Civilization and High-quality Development of Yellow River, Henan Polytechnic University, Jiaozuo; 454000, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 156-163
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: The extraction of rice planting area in county-level depends on the medium and high spatial resolution images of the complete time series. However, it is often difficult to obtain the high spatial resolution images of the complete time series due to the cloud and rain weather and the satellite’s own visit cycle. Thus causing the problem of low precision in rice planting area based on extraction by single MODIS data. Taking Yuanyang County, an excellent rice planting area in Henan Province, as an example, an enhanced spatial and temporal adaptive reflectance fusion model (ESTARFM) was used to fuse mid- and high-resolution Landsat data and high-time-resolution MODIS data to obtain the normalized difference vegetation index (NDVI) data of the complete time series. After smoothing by TIMESAT filtering, the characteristics of time series NDVI curves of rice and other features in the study area were used to set reasonable NDVI thresholds. The decision tree classification method was used to extract the rice planting area. The results showed that the overall classification accuracy was 92.23% and the Kappa coefficient was 0.904 3. The producer accuracy of rice extraction was 96.73% and the user accuracy was 93.51%, which indicated that the ESTARFM model can well integrate high spatial resolution images, solve the problem of missing data, and provide an effective reference for extracting rice planting area in a county-level. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 25
Main heading: Data mining
Controlled terms: Curve fitting? - ?Data fusion? - ?Decision trees? - ?Extraction? - ?Image processing? - ?Image resolution? - ?Radiometers? - ?Time series
Uncontrolled terms: Classification accuracy? - ?Decision tree classification? - ?High spatial resolution images? - ?High-time resolution? - ?Kappa coefficient? - ?Normalized difference vegetation index datum? - ?Spatio-temporal data? - ?Temporal adaptive
Classification code: 723.2 Data Processing and Image Processing? - ?802.3 Chemical Operations? - ?921.6 Numerical Methods? - ?922.2 Mathematical Statistics? - ?944.7 Radiation Measuring Instruments? - ?961 Systems Science
Numerical data indexing: Percentage 9.22e+01%, Percentage 9.35e+01%, Percentage 9.67e+01%
DOI: 10.6041/j.issn.1000-1298.2020.04.018
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
5. Development of Paddy Field Rotary-leveling Machine Based on GNSS
Accession number: 20202008644222
Title of translation: GNSS
Authors: Zhou, Jun (1); Xu, Jiankang (1); Wang, Yaoxi (1); Liang, Youbin (1)
Author affiliation: (1) College of Engineering, Nanjing Agricultural University, Nanjing; 210031, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 38-43
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: The hard bottom layer of the paddy field is not flat, so the rotary tiller will tilt and vibrate when it is working in the field, which will seriously affect the quality and efficiency of the rotary tillage operation and damage the paddy field leveling. In order to solve these problems, a GNSS-controlled intelligent paddy field rotary-leveling machine was developed. The two GNSS satellite antennas were symmetrically fixed at the two ends of the rotary-leveling machine hood, which was used to receive elevation data of the main antenna and pitch angle data between the two antennas. The received elevation positioning data was the elevation of the rotary-leveling machine, and the pitch angle data was the inclination of the rotary-leveling machine. The fuzzy-PID control algorithm was used to output driving voltage signal to the electro-hydraulic proportional reversing valve, thereby controlling the expansion and contraction of the cylinder, so that the rotary-leveling machine rotated around the intermediate rotating shaft or moved up and down along the chute to realize the horizontal and height adjustment of the implement. In order to solve the problem of continuous heating of the hydraulic pump, a hydraulic system was designed. In this hydraulic system, the accumulator and the hydraulic pump worked together to reduce the burden on the hydraulic pump. A datum calculation method was proposed, which automatically calculated the datum plane by the least squares method to get the control reference plane conveniently and quickly. In order to verify the working performance of the intelligent paddy field rotary-leveling machine, the paddy field leveling test was carried out under different crop types such as rice, wheat and different soil types such as sandy soil, clay soil and loam. The test results showed that under different test conditions, the flatness of the paddy field was greatly improved, and the average can reach about 3 cm. The system had good stability and adaptability. After leveling, the paddy field can meet the agronomic requirements of rice planting. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 21
Main heading: Satellite antennas
Controlled terms: Clay? - ?Global positioning system? - ?Hydraulic accumulators? - ?Hydraulic equipment? - ?Least squares approximations? - ?Proportional control systems? - ?Pumps? - ?Three term control systems
Uncontrolled terms: Continuous heating? - ?Electro-hydraulics? - ?Expansion and contraction? - ?Fuzzy - pid controls? - ?Hydraulic system? - ?Least squares methods? - ?Leveling machines? - ?Working performance
Classification code: 483.1 Soils and Soil Mechanics? - ?618.2 Pumps? - ?632.2 Hydraulic Equipment and Machinery? - ?716 Telecommunication; Radar, Radio and Television? - ?731.1 Control Systems? - ?921.6 Numerical Methods
Numerical data indexing: Size 3.00e-02m
DOI: 10.6041/j.issn.1000-1298.2020.04.004
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
6. Effects of Combined Application of Organic and Inorganic Fertilizers on Nitrogen Supply and Crop Water and Nitrogen Utilization in Salinized Soils
Accession number: 20202008644234
Title of translation:
Authors: Zhou, Hui (1); Shi, Haibin (1); Xu, Zhao (1); Guo, Jiawei (1); Fu, Xiaojun (2); Li, Zhengzhong (2)
Author affiliation: (1) College of Water Conservancy and Civil Engineering, Inner Mongolia Agricultural University, Huhhot; 010018, China; (2) Shahaoqu Irrigation Experimental Station, Jiefangzha Management Bureau of Hetao Irrigation District, Bayannur; 015400, China
Corresponding author: Shi, Haibin(shi_haibin@sohu.com)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 299-307
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Hetao Irrigation District (HID) is a main grain production region in China. Soil salinization and excessive application of chemical fertilizers are main important factors that restricting the food and environmental safety in HID. Reasonable and efficient utilization of fertilizer resources on saline soil to improve crop production efficiency and reduce non-point source pollution of nitrogen are the effective ways to relieve the problem. Farmlands with mild (0.460 dS/m) and moderate (0.951 dS/m) salinization were selected, as a pure nitrogen application rate of 240 kg/hm2. The same amount of nitrogen was applied to the different treatments. Five fertilization treatments (the fertilization proportion of organic fertilizer was 0, 25%, 50%, 75% and 100%, respectively) and one blank control were provided, which were designated as U1, U3O1, U1O1, U1O3, O1 and CK, respectively. The field experiment was conducted to explore the response of maize yield to organic nitrogen substituting for inorganic nitrogen fertilizer in different salinized soils, and provide scientific basis for reasonable nitrogen management. Main conclusions were as follows: the amount of nitrogen mineralization in moderate saline soil of the same treatment was significantly lower than that of mild saline soil. In mild saline soil, mineral nitrogen contents added with more inorganic fertilizer were much higher in early growth stage, while a steady increase of mineral nitrogen content was found in soil which combined application of organic and inorganic fertilizer was added during the whole growth period of maize. In moderate saline soil, there was no significant difference in soil mineral nitrogen content in different treatments at the early growth stage, the increase of applied proportion of organic fertilizer was obvious to the improvement of soil mineral nitrogen content in the later stage of crop growth. The corn yield, water and nitrogen use efficiency in moderate saline soil of the same treatment were significantly lower than those in mild saline soil, and the yield was decreased by 30.94%~63.90%(P2 urea+120 kg/hm2 organic fertilizer, and moderate saline soil should be applied with 240 kg/hm2 organic fertilizer. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 57
Main heading: Nitrogen fertilizers
Controlled terms: Crops? - ?Cultivation? - ?Efficiency? - ?Irrigation? - ?Minerals? - ?Nitrogen fixation? - ?Saline water? - ?Soils? - ?Urea
Uncontrolled terms: Hetao irrigation districts? - ?Mineral nitrogen content? - ?Nitrogen application rates? - ?Nitrogen mineralization? - ?Nitrogen-use efficiency? - ?Non-point source pollution? - ?Soil mineral nitrogen? - ?Utilization efficiency
Classification code: 444 Water Resources? - ?482.2 Minerals? - ?483.1 Soils and Soil Mechanics? - ?802.2 Chemical Reactions? - ?804 Chemical Products Generally? - ?804.1 Organic Compounds? - ?821.3 Agricultural Methods? - ?821.4 Agricultural Products? - ?913.1 Production Engineering
Numerical data indexing: Percentage 1.00e+02%, Percentage 1.18e+01%, Percentage 2.50e+01%, Percentage 5.00e+01%, Percentage 7.50e+01%
DOI: 10.6041/j.issn.1000-1298.2020.04.034
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
7. Energy Efficiency Characteristics of Cable Shovel Lifting System Driven by Hydraulic-Electric Hybrid System
Accession number: 20202008644211
Title of translation:
Authors: Wang, Xiangyu (1); Ge, Lei (1); Zhao, Bin (1); Hao, Yunxiao (1); Quan, Long (1); Mu, Xiaopeng (1)
Author affiliation: (1) College of Mechanical and Vehicle Engineering, Taiyuan University of Technology, Taiyuan; 030024, China
Corresponding author: Quan, Long(quanlong@tyut.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 418-426
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Mining shovel is an important equipment in large open pit mining. In lifting operation, the high-quality working device is driven by the lifting motor to lift and shovel into the material to realize excavation. When falling, under the gravity force of the working device, the lifting motor generates electricity. This distributed electric energy is often dissipated in the form of thermal energy through brake resistance, causing great waste of energy. In order to solve the above problems, an innovative driving scheme of hydraulic-electric hybrid shovel hoisting mechanism was proposed. A hydraulic pump/motor was added to the hoisting motor coaxially, and the inlet and outlet of the hydraulic pump/motor were connected with an hydraulic accumulator and tank respectively. When falling, under the action of working device gravity force, the hydraulic pump/motor and lifting motor provided braking torque to control the descending speed. At this time, the hydraulic pump pumped the low-pressure oil in the tank into the accumulator and the gravitational potential energy of the working device was stored in the accumulator; when lifting the working device, the device released high-pressure oil, and the hydraulic pump/motor worked together with the lifting motor to lift the working device, so as to reduce the installed power and energy consumption of the lifting motor. In the research, the working principle of the driving scheme of the hydraulic-electric hybrid driving electric shovel hoisting mechanism was introduced; the principle test-bed was set up to verify the hydraulic-electric hybrid driving scheme; the new hydraulic-electric combined simulation model of the electric shovel was established, and the hydraulic-electric hybrid electric shovel hoisting system was simulated and analyzed. The results showed that the installed power, the peak power and the energy consumption of the motor can be reduced by adopting this scheme. The method can be widely applied to all kinds of heavy lifting equipment driven by motors. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 28
Main heading: Hydraulic accumulators
Controlled terms: Cranes? - ?Energy efficiency? - ?Energy utilization? - ?Gravitation? - ?Hybrid systems? - ?Open pit mining? - ?Potential energy? - ?Pumps? - ?Shovels? - ?Tanks (containers)
Uncontrolled terms: Combined simulation? - ?Efficiency characteristic? - ?Electric energies? - ?Electric hybrid systems? - ?Gravitational potential energy? - ?Hoisting mechanism? - ?Hydraulic pump/motor? - ?Lifting equipments
Classification code: 502.1 Mine and Quarry Operations? - ?525.2 Energy Conservation? - ?525.3 Energy Utilization? - ?618.2 Pumps? - ?619.2 Tanks? - ?632.2 Hydraulic Equipment and Machinery? - ?693.1 Cranes? - ?921 Mathematics? - ?931.5 Gravitation, Relativity and String Theory
DOI: 10.6041/j.issn.1000-1298.2020.04.049
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
8. Feature Extraction of Kiwi Trunk Based on Convolution Layer Feature Visualization
Accession number: 20202008644205
Title of translation:
Authors: Cui, Yongjie (1, 2); Gao, Zongbin (1); Liu, Haozhou (1); Li, Kai (1); Fu, Longsheng (1, 3)
Author affiliation: (1) College of Mechanical and Electronic Engineering, Northwest A&F University, Yangling; Shaanxi; 712100, China; (2) Key Laboratory of Agricultural Internet of Things, Ministry of Agriculture and Rural Affairs, Yangling; Shaanxi; 712100, China; (3) Shaanxi Key Laboratory of Agricultural Information Perception and Intelligent Service, Yangling; Shaanxi; 712100, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 181-190
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: In order to explore the effect of depth of convolution layer on feature extraction of kiwi trunk images, a visualization method was proposed to analyze the extracted features. Firstly, the collected data set was classified into positive and negative samples. Taking the area where the trunk and the water pipe intersected in the dataset as positive samples and the remaining areas as negative samples. Input the samples into LeNet, Alexnet, Vgg-16 and the defined three types of shallow structures for training. Then, by extracting the activation map, normalization, and bicubic interpolation visualization methods, the visualization results of the last convolution layer of each classification model were obtained. The comparison can be obtained: Alexnet and Vgg-16 extracted trunk features in the test image, while LeNet and three types of shallow models extracted the trunk, ridge and other features together while extracting the trunk. Finally, the image classification and object detection models of the above six types of network structures as feature extraction layers were used to verify the flowering period and fruiting period data sets, and the accuracy drop caused by changes in the characteristics of the data sets in different seasons was used as the evaluation criterion: the accuracy of image classification shallow model was decreased by more than 15.90 percentage points, Alexnet and Vgg-16 were decreased by 6.94 percentage points and 2.08 percentage points respectively, the accuracy of object detection shallow model was decreased by more than 49.77 percentage points, Alexnet and Vgg-16 were decreased by 22.53 percentage points and 20.54 percentage points respectively. The accuracy of all shallow models was greatly reduced due to changes in the extracted features. This method explained the difference between the feature extraction of the kiwi trunk target from the deep network and the shallow network from the perspective of visualization, and provided a reference for the adjustment of network depth and training samples in subsequent research. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 33
Main heading: Feature extraction
Controlled terms: Birds? - ?Classification (of information)? - ?Convolution? - ?Extraction? - ?Fruits? - ?Image classification? - ?Object detection? - ?Object recognition? - ?Visualization? - ?Water pipelines
Uncontrolled terms: Bicubic interpolation? - ?Classification models? - ?Evaluation criteria? - ?Network structures? - ?Percentage points? - ?Shallow structure? - ?Visualization method? - ?Visualization results
Classification code: 446.1 Water Supply Systems? - ?716.1 Information Theory and Signal Processing? - ?723.2 Data Processing and Image Processing? - ?802.3 Chemical Operations? - ?821.4 Agricultural Products
DOI: 10.6041/j.issn.1000-1298.2020.04.021
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
9. Recognition Method for Potato Buds Based on Improved Faster R-CNN
Accession number: 20202008643852
Title of translation: Faster R-CNN
Authors: Xi, Rui (1, 2); Jiang, Kai (3); Zhang, Wanzhi (1, 2); Lü, Zhaoqin (1, 2); Hou, Jialin (1, 2)
Author affiliation: (1) College of Mechanical and Electronic Engineering, Shandong Agricultural University, Tai’an; 271018, China; (2) Shandong Agricultural Equipment Intelligent Engineering Laboratory, Tai’an; 271018, China; (3) School of Chemical Engineering, University of Queensland, Brisbane; 4066, Australia
Corresponding author: Hou, Jialin(jlhou@sdau.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 216-223
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: At present, the cutting of seed potatoes is mainly accomplished manually, which caused a series of problems, such as heavy labor intensity, low efficiency and high cost. Thus, the automated cutting of seed potatoes is urgently needed to be solved, especially with the rising cost and decreasing availability of labor. The first and foremost step for automated cutting is the recognition of potato buds. An improved faster region convolutional neural network (Faster R-CNN) scheme was proposed to achieve better recognition performance for potato buds. Data augmentation technique was leveraged to expand the potato dataset. Faster R-CNN model was trained based on the expanded dataset, and experimental results on the test set indicated that the recognition precision was 91.67%, recall rate was 84.09% and F1 was 87.72%. The average running time was 0.183 s. On this basis, an improved Faster R-CNN approach was proposed. Gaussian weight reduction function was adopted to optimize the non-maximum suppression (NMS) algorithm in Faster R-CNN. For the detection boxes which had overlaps with M greater than or equal to the threshold Nt, the corresponding scores was decayed in the improved Faster R-CNN, rather than setting them to zero in Faster R-CNN. Besides, a strategy of online hard example mining (OHEM) with the optimized NMS algorithm was adopted in the improved Faster R-CNN. Experimental results on the test set demonstrated that the improved Faster R-CNN scheme achieved a precision of 96.32%, a recall rate of 90.85% and an F1 of 93.51%, which were increased by 4.65 percentage points, 6.76 percentage points and 5.79 percentage points, respectively, compared with Faster R-CNN. Moreover, the average running time of the improved scheme was 0.183 s, which was the same to that of Faster R-CNN. Namely, the improved scheme could achieve better recognition performance without incurring any noticeable additional computational overhead, thus satisfying the requirements for real-time processing. Consequently, the improved Faster R-CNN approach was effective for potato bud recognition and could lay a solid foundation for future automated cutting of seed potatoes. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 37
Main heading: Convolutional neural networks
Controlled terms: Automation? - ?Statistical tests
Uncontrolled terms: Automated cutting? - ?Average running time? - ?Computational overheads? - ?Data augmentation? - ?Non-maximum suppression? - ?Percentage points? - ?Realtime processing? - ?Recognition methods
Classification code: 731 Automatic Control Principles and Applications? - ?922.2 Mathematical Statistics
Numerical data indexing: Percentage 8.41e+01%, Percentage 8.77e+01%, Percentage 9.08e+01%, Percentage 9.17e+01%, Percentage 9.35e+01%, Percentage 9.63e+01%, Time 1.83e-01s
DOI: 10.6041/j.issn.1000-1298.2020.04.025
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
10. Influence of Backflow Gap Size on Hydraulic Performance of Full-flow Pump
Accession number: 20202008643865
Title of translation:
Authors: Shi, Lijian (1); Jiao, Haifeng (1); Gou, Jinlan (2); Yuan, Yao (3); Tang, Fangping (1); Yang, Fan (1)
Author affiliation: (1) College of Hydraulic Science and Engineering, Yangzhou University, Yangzhou; 225100, China; (2) Wuhan Second Ship Design and Research Institute, Wuhan; 430205, China; (3) Jiangsu Institute of Water Resources Research, Nanjing; 210017, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 139-146
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: In order to study the influence of gap backflow of full-flow pump impeller on hydraulic performance, the CFD software was used to carry out numerical simulation calculation of the full-flow pump. Then the flow characteristics and hydraulic performance of the full-flow pump were analyzed. Finally, the reliability of numerical calculation data was verified through model tests. There were two research directions:the first one was to study performance difference of the full-flow pump under different flow conditions when the gap was constant. The second one was to study the performance difference of the full-flow pump with different gaps under the design condition. The results showed that the gap size had an obvious impact on the hydraulic performance of full-flow pump. With the increase of gap size, the efficiency and head of the pump devices were reduced under the design condition. When the minimum gap size was 0.65 mm, the head of the full-flow pump was 3.05 m under the design condition, and the efficiency was 82.46%. The highest efficiency was 82.66%. When the maximum gap size was 2 mm, the head of the full-flow pump was 2.92 m under the design condition, and the efficiency was 80.85%. The highest efficiency was 81.27%. The difference of the head between two pump devices was 0.13 m under the design condition, and the difference of the efficiency was 1.61 percentage points. With the increase of the flow rate, the difference of the pressure between inlet and outlet was gradually decreased. The backflow rate was also gradually decreased. The influence of backflow on the impeller was small. And close to the rim, the effect of backflow on the flow regime was great. With the increase of the gap size, the backflow of the full-flow pump was increased. The influence of full-flow pump on flow state was heavy. The working ability of the impeller was worse. The head and efficiency of the full-flow pump were gradually decreased. The research can provide a basis for the design and development of the full-flow pump. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 29
Main heading: Computational fluid dynamics
Controlled terms: Computer software? - ?Efficiency? - ?Impellers? - ?Pumps
Uncontrolled terms: Design and Development? - ?Design condition? - ?Flow charac-teristics? - ?Hydraulic performance? - ?Numerical calculation? - ?Numerical simulation calculation? - ?Percentage points? - ?Working abilities
Classification code: 601.2 Machine Components? - ?618.2 Pumps? - ?723 Computer Software, Data Handling and Applications? - ?723.5 Computer Applications? - ?913.1 Production Engineering
Numerical data indexing: Percentage 8.08e+01%, Percentage 8.13e+01%, Percentage 8.25e+01%, Percentage 8.27e+01%, Size 1.30e-01m, Size 2.00e-03m, Size 2.92e+00m, Size 3.05e+00m, Size 6.50e-04m
DOI: 10.6041/j.issn.1000-1298.2020.04.016
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
11. Design and Experiment of Modularized Garlic Combine Harvester
Accession number: 20202008644288
Title of translation:
Authors: Zhao, Dong (1); Cai, Dongmei (1); Qin, Lixiang (1); Gao, Xiang (1); Huang, Weitao (1); Liu, Cheng (1)
Author affiliation: (1) College of Mechanical and Engineering, University of Ji’nan, Ji’nan; 250022, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 95-102
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Inorder to increase the adaptation of garlic harvester to different areas and row spacings, a kind of garlic combine harvester was designed and its key functional parts were also studied in depth. The garlic combine harvester was built by using modularization design methods. The independent harvesting function module had main functions of garlic harvesting such as garlic stem lifter, arrow shaped ripper, belt holding conveyor, garlic stem aligning and cutting device and garlic collector. A 1-rowed to n-rowed garlic combine harvester may be built by choosing the number of harvesting function module with different conveying units and chassises. At the same time, the spaces between the harvesting function modules may be changed steplessly from 0 mm to 300 mm, which will be suitable for 70~420 mm row-spacing garlics mechanized harvesting. Based on the analyses of the influence factors, the garlic drawing forces’ theoretical model was bulit and its changing rule influenced by the structure parameters was also found out. And the experments proved that the drawing forces would be increased with the enlargement of the garlic stem contact angle which may be changed by the adjustment of the belt tension. The drawing force would be enough for the garlic harvesting after the soil ripping when the synchronous belt tension reached 2 800 N. Based on the soil ripping forces’ theoretical model, the changing rules influenced by the angle of the arrow shaped ripper to the ground, the penetrating depth of the ripper and the machine moving velocity were also researched in depth. Results of the orthogonal test showed that the penetrating depth of the ripper and the soil moisture content had significant influence on the soil ripping force. The soil ripping force was 520 N as the penetrating depth of the ripper was 80 mm and the soil moisture content was 30%. Field test results of prototype showed that the technical indicators of the garlic combine harvester met the expected results of design. Its harvesting rate was 98.3%, the loss coefficient which included the damaged and the lost garlic was 3.5% and the production efficiency of 1-rowed harvester was 0.14 hm2/h. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 21
Main heading: Harvesters
Controlled terms: Belts? - ?Combines? - ?Contact angle? - ?Design? - ?Harvesting? - ?Modular construction? - ?Moisture determination? - ?Soil moisture
Uncontrolled terms: Combine harvesters? - ?Mechanized harvesting? - ?Modularization design? - ?Production efficiency? - ?Structure parameter? - ?Synchronous Belts? - ?Technical indicator? - ?Theoretical modeling
Classification code: 405.2 Construction Methods? - ?483.1 Soils and Soil Mechanics? - ?602.1 Mechanical Drives? - ?821.1 Agricultural Machinery and Equipment? - ?821.3 Agricultural Methods? - ?931.2 Physical Properties of Gases, Liquids and Solids? - ?944.2 Moisture Measurements
Numerical data indexing: Force 5.20e+02N, Percentage 3.00e+01%, Percentage 3.50e+00%, Percentage 9.83e+01%, Size 0.00e+00m to 3.00e-01m, Size 7.00e-02m to 4.20e-01m, Size 8.00e-02m
DOI: 10.6041/j.issn.1000-1298.2020.04.011
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
12. Spatio-temporal Distribution Characteristics of Dry-Wet Index in Anhui Province Based on Cloud Mode
Accession number: 20202008644241
Title of translation:
Authors: Sun, Peng (1); Guo, Zhongchen (1); Liu, Na (1); Dai, Hongbao (1); Su, Haimin (1)
Author affiliation: (1) School of Environmental and Surveying Engineering, Suzhou University, Suzhou; 234000, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 147-155
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Spatio-temporal characteristics of dry-wet change are the key characterization of regional hydrological response under global change. To explore the temporal and spatial distribution characteristics of dry-wet index in Anhui Province under the background of global change, spatio-temporal distribution characteristics of aridity index was comprehensively investigated for 15 meteorological stations during 1957-2016 in Anhui Province. Based on the calculation of potential evapotranspiration (ET0) by the FAO 56 Penman-Monteith model with regional correction mode, the temporal and spatial distribution characteristics, uniformity and stability of the dry-wet index (AI) in Anhui Province in the past 60 years were quantitatively described by the cloud model. The AI and ET0 in Anhui Province showed a downward trend, with propensity rates of -0.006 a-1 and -0.583 mm/a, respectively, and P showed an upward trend of 1.155 mm/a. The opposite trend of ET0 and P caused the AI to gradually decrease. Anhui Province generally showed a trend of becoming wet. P was the most discrete and had the worst stability compared with ET0 and AI. On the four-season scale, summer-autumn and winter AI, which was dominated by summer (-0.012 a-1), was the main feature of dry-wet change in Anhui Province. The AI super-entropy value with descending order was summer, autumn, spring and winter, and the uncertainty was gradually reduced. The change entropy of ET0 in the four seasons was lower than the annual average entropy. The ambiguity and randomness of the four seasons’ ET0 were poor. The winter ET0 had the greatest instability. The increase of rain and snow in summer and winter and the decrease of precipitation in spring and autumn were the four seasons’ characteristics in Anhui Province. The main form of the pattern and the summer precipitation were increased significantly (2.467 mm/a), while showing the greatest unevenness and instability. Spatial scale, AI, and P showed the reference crop evapotranspiration variation gradient of Wannan to Wanbei appeared non-smooth latitudes phenomenon, the spatial region of each entropy size was higher than the super time series entropy, and the spatial distribution characteristics of AI were more discrete and unstable. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 38
Main heading: Spatial distribution
Controlled terms: Entropy? - ?Evapotranspiration? - ?Rain? - ?Stability
Uncontrolled terms: Distribution characteristics? - ?Meteorological station? - ?Penman-Monteith models? - ?Potential evapotranspiration? - ?Reference crop evapotranspirations? - ?Spatiotemporal characteristics? - ?Spatiotemporal distributions? - ?Temporal and spatial distribution
Classification code: 443.3 Precipitation? - ?641.1 Thermodynamics? - ?921 Mathematics
Numerical data indexing: Age 6.00e+01yr
DOI: 10.6041/j.issn.1000-1298.2020.04.017
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
13. Citrus Detection Method in Night Environment Based on Improved YOLO v3 Network
Accession number: 20202008643835
Title of translation: YOLO v3
Authors: Xiong, Juntao (1); Zheng, Zhenhui (1); Liang, Jiaen (1); Zhong, Zhuo (1); Liu, Bolin (1); Sun, Baoxia (2)
Author affiliation: (1) College of Mathematics and Informatics, South China Agricultural University, Guangzhou; 510642, China; (2) Guangdong Mechanical and Electrical Polytechnic, Guangzhou; 510515, China
Corresponding author: Sun, Baoxia(sunbaoxia@126.com)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 199-206
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: In China, citrus production occupies an important position in agriculture and has great economic benefit. For a long time, most of citrus harvesting relies on manual work, which has low efficiency and high labor cost. The labor cost accounts for almost one-half of total labor cost in citrus production process. In addition, citrus picking is usually carried out during the day, while makes less use of night time. Therefore, it is of great significance to develop a fruit picking robot working at nighttime. Focusing on citrus picking process, a multi-scale convolution neural network named Des-YOLO v3 was proposed and used to detect citrus at nighttime under natural environment. By using ResNet and DenseNet for reference, the Des-YOLO v3 network was designed to realize the reuse and fusion of multi-layer features of the network, which strengthened the robustness of small target and overlapping occlusion fruit recognition, and significantly improved the precision of fruit detection. The experimental results showed that the precision, recall rate and F1 value of the Des-YOLO v3 network were 97.67%, 97.46% and 0.976, respectively, while those of YOLO v3 network were 91.41%, 91.10% and 0.913, respectively. At the same time, the mean average precision of the trained model under the test set was 90.75%, and the detection speed was 53 f/s, which was 2.27 percentage points and 11 f/s higher than those of YOLO v3_DarkNet53, respectively. The final results showed that the Des-YOLO v3 recognition network had stronger robustness and higher detection precision for the recognition of mature citrus in the complex field environment at night, which provided technical support for the visual recognition of citrus picking robot. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 22
Main heading: Wages
Controlled terms: Agricultural robots? - ?Cost accounting? - ?Employment? - ?Fruits
Uncontrolled terms: Citrus harvesting? - ?Convolution neural network? - ?Detection precision? - ?Economic benefits? - ?Fruit recognition? - ?Natural environments? - ?Percentage points? - ?Visual recognition
Classification code: 821.4 Agricultural Products? - ?911.1 Cost Accounting? - ?912.4 Personnel
Numerical data indexing: Percentage 9.08e+01%, Percentage 9.11e+01%, Percentage 9.14e+01%, Percentage 9.75e+01%, Percentage 9.77e+01%
DOI: 10.6041/j.issn.1000-1298.2020.04.023
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
14. Design and Experiment of Combination Air Scrubbing System for Large-scale Pig House
Accession number: 20202008643866
Title of translation:
Authors: Wang, Yu (1, 2); Wu, Peng (1, 2); Zeng, Zhixiong (1, 2); Wang, Guanghai (1, 2); Dong, Bing (1, 2); Lü, Enli (1)
Author affiliation: (1) College of Engineering, South China Agricultural University, Guangzhou; 510642, China; (2) Key Laboratory of Key Technology on Agricultural Machine and Equipment, Ministry of Education, South China Agricultural University, Guangzhou; 510642, China
Corresponding author: Lü, Enli(enlilv@scau.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 344-352
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: An air scrubbing system was developed to efficiently treat the exhaust emission from large-scale pig house. The system utilized a combined scrubbing system that involved chemical method and water-washing method. The real-time dynamic environmental data, including pH value, EC value, liquid level and differential pressure were collected. The intelligent control strategy was established via programmable logic controller (PLC) control system to regulate the start-up of the washing pump and electron magnetic valve. In this manner, four work links: water supply, acid addition, spraying and waste emission were conducted automatically. At the mean time, the control system utilized MCGS touch screen to establish communication connection with PLC. In particular, the human machine interface was created to realize the monitor of system environmental data, dynamic display of operation process, configure system parameters, system alarm and other functions needed. Therefore, the system achieved the purpose of monitoring and controlling on the whole purification process, as well as satisfied the simple operation of system and visualization of the whole scrubbing process. Moreover, the system can also implement a variety of control modes according to the requirements of efficiency and economy in practical applications. It was found that all control modes were able to inhibit the emission of pig house effectively. The experimental results indicated that the removal rate of ammonia gas can reach 85%. The overall system was entirely well operated and easily controlled, and the economic costs were clearly quantified as well. This gas scrubbing system was successfully applied to a pig breeding farm in Jiangxi Province, which provided significant reference of air scrubbing techniques for livestock operations in practical engineering. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 27
Main heading: Monitoring
Controlled terms: Agriculture? - ?Ammonia? - ?Control systems? - ?Electron tubes? - ?Houses? - ?Mammals? - ?Man machine systems? - ?Touch screens? - ?Washing? - ?Water supply
Uncontrolled terms: Communication connection? - ?Differential pressures? - ?Efficiency and economies? - ?Human Machine Interface? - ?Intelligent control strategies? - ?Monitoring and controlling? - ?Practical engineering? - ?Programmable logic controllers (PLC)
Classification code: 402.3 Residences? - ?446.1 Water Supply Systems? - ?714.1 Electron Tubes? - ?722.2 Computer Peripheral Equipment? - ?731.1 Control Systems? - ?804.2 Inorganic Compounds? - ?821 Agricultural Equipment and Methods; Vegetation and Pest Control
Numerical data indexing: Percentage 8.50e+01%
DOI: 10.6041/j.issn.1000-1298.2020.04.039
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
15. Performance Characterization of DRP Greenhouse Transparent Covering Material
Accession number: 20202008644216
Title of translation: DRP
Authors: Wang, Yuxin (1); Li, Danchun (1); Huang, Bin (2); Xie, Xin (2); Feng, Ronghui (2)
Author affiliation: (1) College of Water Resources and Civil Engineering, China Agricultural University, Beijing; 100083, China; (2) Shuyang Zhengzhong New Materials Co., Ltd., Suqian; 223800, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 320-327
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: PET slices and masterbatch with organic synthetic additives were the main raw materials. Through crystallization drying, melt extrusion casting and longitudinal and transverse stretching, a degradable and recycled polyester agricultural film (DRP film) with high thermal insulation, high transparency, high strength and aging resistance was developed. The radiation transmittance, heat preservation ability, tensile properties, tear resistance, thermal stability and aging resistance of the DRP film were characterized by means of comparative analysis using spectrophotometer, universal testing machine and thermogravimetric analyzer. The results showed that the transmittance of DRP films in photosynthetic effective radiation wave range was 90.73%. The transmittance of ultraviolet radiation B and mid-infrared was 0.74% and 14.56%, respectively, which showed that DRP film had a good ability to resist the ultraviolet radiation B and the heat preservation at night. In addition, by comparing the radiation transmittance properties of DRP films aged naturally for about one year over the greenhouse with that of initial DRP films, it was found that DRP films aged naturally declined only 3 percentage points in photosynthetic effective radiation wave range, and it still had good light transmittance. The radiation transmittance of DRP film was decreased only by 4.34 percentage points in 5 000~25 000 nm after aging, and it still had good heat preservation ability as the film of greenhouse at night. The longitudinal tensile strength of DRP film was 103.21 MPa, which could meet the requirements of normal use. The longitudinal trouser tear strength of DRP film was 244.17 kN/m, which was 19.49 times of that of PET film. DRP film had three obvious weightlessness phenomena during the temperature rise to 600 in thermogravimetric test. The first weightlessness temperature of DRP film was (250±5), and it had better thermal stability. In conclusion, the DRP greenhouse transparent cover material had outstanding advantages in light transmission, heat preservation, mechanical properties and aging resistance. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 26
Main heading: Heat resistance
Controlled terms: Ability testing? - ?Additives? - ?Agricultural robots? - ?Greenhouses? - ?Light transmission? - ?Melt spinning? - ?Radiation? - ?Tensile strength? - ?Tensile testing? - ?Thermal insulation ? - ?Thermodynamic stability? - ?Thermogravimetric analysis? - ?Ultraviolet radiation? - ?Weightlessness
Uncontrolled terms: Comparative analysis? - ?Longitudinal tensile strengths? - ?Performance characterization? - ?Radiation transmittances? - ?Thermogravimetric analyzers? - ?Thermogravimetric test? - ?Transverse stretching? - ?Universal testing machines
Classification code: 413.2 Heat Insulating Materials? - ?641.1 Thermodynamics? - ?656.1 Space Flight? - ?741.1 Light/Optics? - ?801 Chemistry? - ?803 Chemical Agents and Basic Industrial Chemicals? - ?821.6 Farm Buildings and Other Structures? - ?912.4 Personnel
Numerical data indexing: Percentage 1.46e+01%, Percentage 7.40e-01%, Percentage 9.07e+01%, Pressure 1.03e+08Pa, Size 5.00e-06m to 2.50e-05m, Surface_Tension 2.44e+05N*m
DOI: 10.6041/j.issn.1000-1298.2020.04.036
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
16. Establishment and Experiment of Quadratic Residual Compensation Atomization Model of Electricity Atomizer
Accession number: 20202008644294
Title of translation:
Authors: Zhao, Chunjiang (1, 2); Chai, Shufan (1, 3); Chen, Liping (3, 4); Zhang, Ruirui (3, 4); Li, Longlong (3, 4); Tang, Qing (3, 4)
Author affiliation: (1) College of Mechanical and Electronic Engineering, Northwest A&F University, Yangling; Shaanxi; 712100, China; (2) Beijing Research Center for Information Technology in Agriculture, Beijing; 100097, China; (3) National Engineering Research Center of Intelligent Equipment for Agriculture, Beijing; 100097, China; (4) National Center for International Research on Agricultural Aerial Application Technology, Beijing; 100097, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 19-27 and 37
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: In order to solve the problem of precise control of droplet diameter variables during aviation spray, the quadratic regression orthogonal experiment and machine learning was used to establish the quadratic residual compensation droplet diameter model. With Aerial-E electricity atomizer as the control object, the quadratic regression orthogonal experiment was carried out on the atomization experiment platform to analyze the correlation between the droplet diameter and the wind speed, flow rate, atomizer speed, and droplet diameter model was established. In order to improve the prediction accuracy, a compensation factor was added to establish the first optimized droplet diameter compensation model. To further improve the prediction accuracy, the second residual prediction model was established by machine learning, the second residual prediction model and the first optimized droplet diameter compensation model were superimposed linearly to obtain the quadratic residual compensation droplet diameter model. In order to verify the validity of the quadratic residual compensation droplet diameter model, the model validation experiment and the comparative experiment were carried out, the results showed that the maximum deviation predicted by the quadratic residual compensation droplet diameter model was 10.78%, the R2 between the predicted and measured values of the quadratic residual compensation droplet diameter model was 0.95, which was 0.06 higher than that of the droplet diameter model and 0.05 higher than that of the first optimized droplet diameter compensation model. The quadratic residual compensation atomization model of electricity atomizer was obtained by equivalent deformation of the quadratic residual compensation droplet diameter model, and an electricity atomization system was designed based on the model. A system application experiment was carried out to verify the practicality of the system, the results showed that the R2 between the expected and the measured value of the droplet diameter was 0.94, and the relative span of droplet was less than 1.6, which could realize the control of the droplet diameter under the condition of stable wind speed and flow rate. The results can realize precise control of droplet diameter variables during aviation spray. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 31
Main heading: Drop breakup
Controlled terms: Antennas? - ?Atomization? - ?Forecasting? - ?Machine learning? - ?Wind
Uncontrolled terms: Atomization models? - ?Comparative experiments? - ?Compensation factor? - ?Compensation modeling? - ?Experiment platforms? - ?Prediction accuracy? - ?Quadratic regression orthogonal experiments? - ?System applications
Classification code: 443.1 Atmospheric Properties? - ?802.3 Chemical Operations? - ?931.2 Physical Properties of Gases, Liquids and Solids
Numerical data indexing: Percentage 1.08e+01%
DOI: 10.6041/j.issn.1000-1298.2020.04.002
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
17. Soil Thickness Measuring Method Based on Non-uniform Speed Modified Cone Index
Accession number: 20202008644146
Title of translation:
Authors: Li, Li (1, 2); Fu, Xue (3); Yun, Wenju (4); Tang, Huaizhi (1, 2); Zhang, Chao (1, 2)
Author affiliation: (1) College of Land Science and Technology, China Agricultural University, Beijing; 100083, China; (2) Key Laboratory of Agricultural Land Quality, Ministry of Natural Resources, Beijing; 100035, China; (3) College of Information and Electrical Engineering, China Agricultural University, Beijing; 100083, China; (4) Land Consolidation and Rehabilitation Center, Ministry of Natural Resources, Beijing; 100035, China
Corresponding author: Tang, Huaizhi(Tanghz@cau.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 291-298
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Soil thickness is an important parameter affecting soil quality. Rapid acquisition of accurate soil thickness information is an important data basis for the analysis and evaluation of the quality of cultivated land resources and its changing trend. Current mainstream measurement methods are inefficient or inaccurate, such as radar detection method and borehole sampling method. The rapid measurement of soil thickness was realized based on soil mechanical resistance with optimized cone meter. Data were acquired by a cone soil thickness measuring instrument which was an optimized hand-held cone meter attached with acceleration sensor, position sensor and other sensors. Acceleration compensation technology was adopted to reduce the measurement error of soil mechanical resistance caused by non-uniform speed penetration of cone meter. Envelope detection and Hilbert instantaneous amplitude eigenvalue clustering algorithm were introduced to identify soil structure and calculate the thickness of soil layer. The simulation results based on Ayers semi-empirical model showed that the conical soil thickness measuring instrument based on Hilbert transform algorithm can effectively acquire the information of soil thickness with relative error no higher than 7.50%. The measuring results for outdoor measured data showed that the absolute error of soil thickness measured by Hilbert instantaneous amplitude spectrum based on lower envelope was not more than 1 cm, and the relative error was not more than 10%. This method can meet the needs of actual measurement for plough layer soil depth and provide a reference for future soil layer measuring application. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 26
Main heading: Soil surveys
Controlled terms: Acceleration? - ?Clustering algorithms? - ?Eigenvalues and eigenfunctions? - ?Error compensation? - ?Quality control? - ?Soils? - ?Tracking radar
Uncontrolled terms: Analysis and evaluation? - ?Compensation technology? - ?Instantaneous amplitude? - ?Instantaneous amplitude spectrums? - ?Measuring applications? - ?Measuring instruments? - ?Semi-empirical modeling? - ?Soil mechanical resistance
Classification code: 483.1 Soils and Soil Mechanics? - ?716.2 Radar Systems and Equipment? - ?903.1 Information Sources and Analysis? - ?913.3 Quality Assurance and Control
Numerical data indexing: Percentage 1.00e+01%, Percentage 7.50e+00%, Size 1.00e-02m
DOI: 10.6041/j.issn.1000-1298.2020.04.033
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
18. Root Phenotypic Detection of Different Vigorous Maize Seeds Based on Corrosion Growth Algorithm of Image
Accession number: 20202008644204
Title of translation:
Authors: Lu, Wei (1, 2); Li, Ye (1, 2); Wang, Ling (1, 2); Luo, Hui (1, 2); Sun, Guoxiang (1, 2); Wang, Xiaochan (1, 2)
Author affiliation: (1) College of Engineering, Nanjing Agricultural University, Nanjing; 210031, China; (2) Engineering Laboratory of Modern Facility Agriculture Technology and Equipment in Jiangsu Province, Nanjing; 210031, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 224-231
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: The root phenotypes of different vigorous maize seeds vary a lot, and imaging roots of growing maize is a non-invasive, affordable and high throughput way to detect it. However, due to the block of soil, acquiring a complete image is difficult. An algorithm was proposed to repair incomplete root images and based on it, root fast non-invasive phenotyping detection can be realized. Firstly, a cuboid transparent container without cover was developed as mesocosms and the maize seeds were planted in it. The maize roots grew in soil against two acrylic plastic surfaces due to the press of the small growing area to acquire more root details during roots visualization and imaging. Even though, parts of the roots were occluded by the soil which meant that it was tough to extract the information of root general physical construction. For recovering gaps from disconnected root segments, corrosion growth algorithm was proposed based on the physiological characteristics of hydrotropism, geostrophic and continuity with three steps which were root image thinning, corrosion and growing processing, respectively. The experiments indicated that maize phenotyping parameters were negatively correlated with seed aging days. And specifically, root number, root length, root width and root extension length of unaged and 14-day-aged maize seeds were decreased from 14.80, 83.50 mm, 1.53 mm and 82.70 mm to 4.38, 36.90 mm, 1.38 mm and 54.6 mm, and the growing speed of them were changed from 1.68 per day, 8.80 mm/d, 0.06 mm/d, 9.0 mm/d to 0.70 per day, 4.3 mm/d, 0.05 mm/d and 5.70 mm/d, respectively. Whereas root extension angle is basically irrelevant with the level of maize seed aging. The developed cuboid transparent container without cover can push each root growing along the wall of the container which helped to acquire more root information. The presented novel corrosion growth algorithm can recover the missing parts, even for big gaps, of maize roots effectively according to root morphological properties. The experiments showed that the proposed method can be applied to evaluate the vigor of maize seeds which had vast application prospect in high throughput root phenotyping area. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 38
Main heading: Image thinning
Controlled terms: Containers? - ?Corrosion? - ?Plants (botany)? - ?Seed? - ?Soils
Uncontrolled terms: Application prospect? - ?Corrosion growth? - ?High throughput? - ?Morphological properties? - ?Physiological characteristics? - ?Plastic surfaces? - ?Root extensions? - ?Root segments
Classification code: 483.1 Soils and Soil Mechanics? - ?723.2 Data Processing and Image Processing? - ?821.4 Agricultural Products
Numerical data indexing: Size 1.38e-03m, Size 1.53e-03m, Size 3.69e-02m, Size 5.46e-02m, Size 8.35e-02m
DOI: 10.6041/j.issn.1000-1298.2020.04.026
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
19. Influence of Long and Short Blades Trailing Edge Shape on Performance and Rotor-stator Interaction in Centrifugal Pump
Accession number: 20202008644188
Title of translation:
Authors: Zhang, Jinfeng (1); Cai, Haikun (1); Chen, Shengbo (1); Xu, Jie (1); Li, Yalin (1)
Author affiliation: (1) National Research Center of Pumps, Jiangsu University, Zhenjiang; 212013, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 122-130 and 190
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: The change of blade trailing edge shape will affect the wake structure of impeller outflow, which has a significant impact on rotor-stator interaction (RSI) in the pump. To study the influence of long and short blades trailing edge shape on performance and rotor-stator interaction in centrifugal pump by CFD, long and short blades trailing edge filing was applied on pressure and suction sides with different thicknesses respectively. The numerical simulation was carried out by using the SST-SAS turbulence model, and the accuracy of the simulation was verified by performance and PIV test. Rotor-stator interaction in pump was analyzed by pressure fluctuation and vorticity distribution. The results showed that pressure side filing (PSF) can effectively improve the efficiency of centrifugal pump at nominal flow rate, and the greater the filing thickness was, the more remarkable the effect was. On the other hand, PSF can also obviously improve RSI in centrifugal pump at nominal flow rate, so as to reduce the energy loss of pressure fluctuation, improve the performance of centrifugal pump and prolong the service life of blades, while the suction side filing (SSF) greatly aggravated the rotor-stator interaction. The distribution of pressure fluctuation and vorticity in frequency domain showed that the main frequency components of RSI in impeller passage were axial frequency and its multiplication, and the main frequency and secondary frequency of RSI in volute passage were fB and 0.5fB respectively. Compared with the main frequency vorticity near the trailing edge of the long and short blades, the effect of the trailing edge filing of short blade was more significant than that of the long blade. Evolution process of the vortices in RSI region demonstrated that the vortices in RSI region during short blade passed through the tongue were more intense compared with long blade, which determined the difference of RSI near the trailing edge of the long and short blades and resulted in a secondary frequency of 0.5fB. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 25
Main heading: Stators
Controlled terms: Axial flow? - ?Centrifugal pumps? - ?Computational fluid dynamics? - ?Energy dissipation? - ?Frequency domain analysis? - ?Impellers? - ?Turbulence models? - ?Vortex flow? - ?Vorticity
Uncontrolled terms: Evolution process? - ?Frequency domains? - ?Impeller passage? - ?Main frequency? - ?Pressure fluctuation? - ?Rotor-stator interactions? - ?Vorticity distribution? - ?Wake structures
Classification code: 525.4 Energy Losses (industrial and residential)? - ?601.2 Machine Components? - ?618.2 Pumps? - ?631.1 Fluid Flow, General? - ?705.1 Electric Machinery, General? - ?723.5 Computer Applications? - ?921.3 Mathematical Transformations
DOI: 10.6041/j.issn.1000-1298.2020.04.014
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
20. Effects of Irrigation Amounts and Groundwater Regulation on Soil Water and Salt Distribution in Arid Region
Accession number: 20202008644273
Title of translation:
Authors: Shi, Haibin (1); Guo, Jiawei (1); Zhou, Hui (1); Wang, Guoshuai (1); Fu, Xiaojun (2); Li, Zhengzhong (2)
Author affiliation: (1) College of Water Conservancy and Civil Engineering, Inner Mongolia Agricultural University, Huhhot; 010018, China; (2) Shahaoqu Irrigation Experimental Station, Jiefangzha Management Bureau of Hetao Irrigation District, Bayannur; 015400, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 268-278
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: In arid oases irrigation areas, soil secondary salination is one of the main problems leading to land desertification, so as to imperil the soil quality, growing of crops and agricultural production, even leading to abandonment of agricultural soils. Most salinization processes of salt accumulation in irrigated lands are largely determined by the salinity of the irrigation water and the groundwater level in the areas. So it is very crucial to control groundwater and irrigation amount for agricultural development. In order to find out the optimal irrigation amount and reasonable groundwater depth in typical cultivated land in Hetao Irrigation District, field trials were conducted for two consecutive years in 2017 and 2018, and sunflower farmland was selected as the research object, saturated-unsaturated soil moisture and solute motion theory was applied, and HYDRUS-2D numerical model was utilized for numerical simulation of water and salt transport in GSPAC system under different irrigation and groundwater depth conditions in the study area, and analysis of water and salt transport conditions under different irrigation conditions was made to determine the optimal irrigation system and reasonable groundwater depth. The simulation results were compared with the field test results, and the model simulation values were in good agreement with the measured values. The results showed that the optimal irrigation amount in the test area was 82.8~85.5 mm, and the reasonable grounding depth of groundwater was 160.72 cm. The research can provide a theory basis for rational utilization of water resources and water-salt regulation in arid regions. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 40
Main heading: Irrigation
Controlled terms: Agricultural robots? - ?Arid regions? - ?Cultivation? - ?Groundwater? - ?Groundwater resources? - ?Numerical models? - ?Soil moisture? - ?Soil testing
Uncontrolled terms: Agricultural development? - ?Agricultural productions? - ?Ground water depths? - ?Groundwater regulation? - ?Hetao irrigation districts? - ?Land desertification? - ?Salinization process? - ?Water and salt transports
Classification code: 443 Meteorology? - ?444 Water Resources? - ?444.2 Groundwater? - ?483.1 Soils and Soil Mechanics? - ?821.3 Agricultural Methods? - ?921 Mathematics
Numerical data indexing: Size 1.61e+00m, Size 8.28e-02m to 8.55e-02m
DOI: 10.6041/j.issn.1000-1298.2020.04.031
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
21. Persistent Effect of Biochar on Soil Water Diffusion and Solute Dispersion in Black Soil Region
Accession number: 20202008644263
Title of translation:
Authors: Wei, Yongxia (1, 2); Wang, He (1); Xiao, Jingping (1); Liu, Hui (2, 3)
Author affiliation: (1) School of Water Conservancy and Civil Engineering, Northeast Agricultural University, Harbin; 150030, China; (2) Key Laboratory of High Efficiency Utilization of Agricultural Water Resources, Ministry of Agriculture and Rural Affairs, Northeast Agricultural University, Harbin; 150030, China; (3) School of Science, Northeast Agricultural University, Harbin; 150030, China
Corresponding author: Liu, Hui(xiaolaida@163.com)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 308-319
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: In order to explore the effect of applying biochar on soil water diffusion and solute dispersion in sloping farmland in black soil area, the biochar effect test was carried out on a typical slope of 1.5°, 3° and 5° in 2016-2019. The effects of carbon on soil bulk density, porosity, organic matter content, Boltzmann transformation parameter (ξ), unsaturated soil water diffusion rate D(θ), and unsaturated soil hydrodynamic diffusion coefficient Dsh(θ) in the single application of biochar were analyzed. The results showed that the soil bulk density was significantly decreased, and soil porosity and soil organic matter content were significantly increased in the soil within a year after the addition of biochar. And the changing rate of each index was decreased with the increase of slope and the extension of carbonation period. Among the three factors of slope, year and whether to apply biochar, the most significant effects on soil bulk density, porosity, organic matter content were whether or not to apply biochar. Biochar increased the ξ, and the ξ was increased with the slope of soil, and the length of carbon was reduced year by year. From 2016 to 2019, D(θ) and Dsh(θ) were both increased rapidly with the increase of soil water content (θ). When θ≤0.42 cm3/cm3, biochar inhibited soil moisture diffusion, and when θ>0.42 cm3/cm3, biochar promoted soil water diffusion. When θ≤0.36 cm3/cm3, biochar inhibited the dispersion of NaCl solution in the soil, and when θ>0.36 cm3/cm3, biochar can promote the dispersion of NaCl solution in the soil. The soil water content in experimental zone was in the range of 0.20~0.35 cm3/cm3, thus the biochar had an inhibitory effect on water diffusion and NaCl solution dispersion, and the effect of biochar on water diffusion and solution dispersion was decreased with the increase of slope and prolonged years after charcoal application. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 43
Main heading: Soil moisture
Controlled terms: Biogeochemistry? - ?Carbon? - ?Charcoal? - ?Diffusion in liquids? - ?Dispersions? - ?Organic compounds? - ?Porosity? - ?Sodium chloride
Uncontrolled terms: Black soil regions? - ?Boltzmann transformations? - ?Inhibitory effect? - ?Moisture diffusion? - ?Organic matter content? - ?Soil organic matter contents? - ?Soil water content? - ?Solute dispersions
Classification code: 481.2 Geochemistry? - ?483.1 Soils and Soil Mechanics? - ?524 Solid Fuels? - ?804 Chemical Products Generally? - ?804.1 Organic Compounds? - ?931.2 Physical Properties of Gases, Liquids and Solids? - ?951 Materials Science
DOI: 10.6041/j.issn.1000-1298.2020.04.035
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
22. Method and Experiment of Maize (Zea Mays L.) Stems Recognition Based on Deep Learning and Image Processing
Accession number: 20202008644233
Title of translation:
Authors: Liu, Huili (1); Jia, Honglei (1, 2); Wang, Gang (1, 3); Glatzel, Stephan (3); Yuan, Hongfang (1); Huang, Dongyan (1, 2)
Author affiliation: (1) College of Biological and Agricultural Engineering, Jilin University, Changchun; 130022, China; (2) Key Laboratory of Bionic Engineering, Ministry of Education, Jilin University, Changchun; 130022, China; (3) Department of Geography and Regional Research, University of Vienna, Vienna; 1090, Australia
Corresponding author: Wang, Gang(gw1988@jlu.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 207-215
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Modern agricultural equipment is developing towards the intelligent machinery, and deep learning and machine vision are core technologies in realizing the intelligent machinery. In terms of the machine-vision based intelligent agricultural machinery that works in maize field, they should forward towards at the maize stem or avoiding the maize stem, while the ability to identify the maize stem accurately is the premise to ensure them work properly. Aiming to distinguish the maize (Zea Mays L.) stems, which grew in the field. In order to acquire the high quality field pictures, one charge-coupled device (CCD) camera was mounted in one camera gimbal. The plug-in unit named after LabelImage was applied to mark and label the maize plants, based on the deep learning framework TensorFlow, a convolution neural network model with multi-scale hierarchical features was built, and the unit convolution kernel with four times expansion was applied. Thus the maize seedling recognition model was obtained with the recognition accuracy of 99.65%. Based on the recognition results, the morphological process was conducted by the OpenCV 3.4.2 and the Python 3.6.5. The threshold value exerted the major influence on depending the information completeness during the binary process, the pictures that contained the maize seedlings were divided into an optimum parts, then an optimum threshold value for each part would be calculated by the algorithm that described. Inspired by the bounding rectangle of each object was different in the binary picture, the aspect ratio was utilized to distinguish the maize seedling stem, and the minimum aspect ratio was computed, then the corresponding bounding rectangle was filled red which indicated the stems. The field experiment was conducted from June 20th to June 22nd 2018, and totally 10 800 pictures were shot during these three days. Five shooting times and six kinds of weed densities were took into consideration for each day. The experimental results showed that the mean identification accuracy was 98.93%, and neither the shooting times (P>0.05) nor the weed densities (P>0.05) had significant influence on the recognition accuracies. The research result had applicable value, and it can be used as the upstream technology for the intelligent agricultural equipment. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 29
Main heading: Deep learning
Controlled terms: Agricultural robots? - ?Aspect ratio? - ?Cameras? - ?Charge coupled devices? - ?Computer vision? - ?Convolution? - ?Grain (agricultural product)? - ?Learning systems
Uncontrolled terms: Agricultural equipment? - ?Convolution neural network? - ?Hierarchical features? - ?Identification accuracy? - ?Information completeness? - ?Learning frameworks? - ?Morphological process? - ?Recognition accuracy
Classification code: 714.2 Semiconductor Devices and Integrated Circuits? - ?716.1 Information Theory and Signal Processing? - ?723.5 Computer Applications? - ?742.2 Photographic Equipment? - ?821.4 Agricultural Products
Numerical data indexing: Percentage 9.89e+01%, Percentage 9.97e+01%
DOI: 10.6041/j.issn.1000-1298.2020.04.024
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
23. Bench Test and Analysis on Performance of Autofollow Row for Traction Sugar Beet Combine Harvester
Accession number: 20202008643842
Title of translation:
Authors: Wang, Shenying (1, 2); Hu, Zhichao (1, 2); Chen, Charles (3); Gao, Xuemei (1, 2); Gu, Fengwei (1, 2); Wu, Huichang (1, 2)
Author affiliation: (1) Nanjing Institute for Agricultural Mechanization, Ministry of Agriculture and Rural Affairs, Nanjing; 210014, China; (2) Key Laboratory of Modern Agricultural Equipment, Ministry of Agriculture and Rural Affairs, Nanjing; 210014, China; (3) College of Agriculture, Auburn University, Auburn; AL; 36849, United States
Corresponding author: Hu, Zhichao(nfzhongzi@163.com)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 103-112 and 163
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Aiming to improve the automation level and operation performance of sugar beet harvesting machinery in China, reduce the loss of damage and leakage digging, and reduce the labor intensity of personnel, 4LT-A type traction sugar beet combine harvester and 4LTSYT-A autofollow row field simulation experiment platform were developed, and the kinematics analysis of autofollow row system was also carried out. During the tests, the 4LTSYT-A autofollow row field simulation experiment platform was placed under the beet root deviation distance detection mechanism and digging mechanism of the 4LT-A type beet combine harvester, and its power was provided by the variable frequency motor controlled by the control box. The 4LT-A type beet combine harvester was towed and powered by a John Deere 1054 tractor. Single factor bench tests were carried out by taking leakage digging rate, damage rate and response time as the autofollow row performance indexes, and taking reset spring preload force, forward speed, deviation distance, hydraulic flow and oil supply pressure and plant spacing as test factors. The significance and influence of each factor on each performance index were analyzed. The variance analysis and visual analysis of the single factor test results showed that the spring preload force, forward speed, deviation distance and hydraulic flow had significant effects on each performance index, the oil supply pressure and plant spacing had no significant effect on each performance index. With the increase of spring preloading force (range of 53~346 N), the response time was increased, and the leakage digging rate and damage rate was firstly decreased and then increased. When the preloading force was 198 N, the leakage digging rate and damage rate were the lowest, which were respectively 2.34% and 3.77%. With the increase of forward speed, the leakage digging rate and damage rate were increased gradually, and the response time was decreased gradually and tended to be constant. When the hydraulic flow was changed from 15 L/min to 35 L/min, the leakage digging rate was gradually decreased, and the response time and damage rate were first decreased and then increased. When the hydraulic flow q=25 L/min, the damage rate and response time were the smallest, which were 3.77% and 0.47 s, respectively. Each performance index was increased gradually with the increase of deviation distance, and the autofollow row system had a good adaptability to the deviation distance of 0~6 cm. This research can provide reference for the later parameter optimization and the research of automatic row harvesting system of beet and other undersoil fruit harvesters. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 22
Main heading: Leakage (fluid)
Controlled terms: Energy resources? - ?Harvesters? - ?Response time (computer systems)? - ?Simulation platform? - ?Sugar beets? - ?Testing
Uncontrolled terms: Combine harvesters? - ?Deviation distances? - ?Experiment platforms? - ?Kinematics analysis? - ?Operation performance? - ?Parameter optimization? - ?Performance indices? - ?Variable frequency motors
Classification code: 525.1 Energy Resources and Renewable Energy Issues? - ?821.1 Agricultural Machinery and Equipment? - ?821.4 Agricultural Products
Numerical data indexing: Force 1.98e+02N, Force 5.30e+01N to 3.46e+02N, Percentage 2.34e+00%, Percentage 3.77e+00%, Size 0.00e+00m to 6.00e-02m, Time 4.70e-01s
DOI: 10.6041/j.issn.1000-1298.2020.04.012
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
24. Design of Protein Content Detector for Raw Milk Based on Electrical Properties
Accession number: 20202008644208
Title of translation:
Authors: Guo, Wenchuan (1, 2); Liu, Zhenhua (1); Zhu, Xinhua (1)
Author affiliation: (1) College of Mechanical and Electronic Engineering, Northwest A&F University, Yangling; Shaanxi; 712100, China; (2) Key Laboratory of Agricultural Internet of Things, Ministry of Agriculture and Rural Affairs, Yangling; Shaanxi; 712100, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 387-393
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Protein content is one of the most important quality indicators of milk. The traditional methods used to measure the protein content of milk have the advantage of high precision, but the measurement procedures are tedious and time-consuming, and the measurement equipment are expensive. In addition, these methods cannot be used in filed or in-suit. Therefore, developing a kind of portable milk protein content detector which is simple in operation and low in cost, and could be used in-suit measurement, will be appreciated by milk producers, processers and consumers. Since the values of electric parameters of milk are affected by protein content, a portable protein content detector over the frequency range of 1~100 MHz was developed. The hardware of the detector consisted of a STM32 single chip microcomputer, a frequency sweep signal source module, a detection module, a signal processing module, and an input and output modules. The software, developed under the development environment of MDK 5.0 by using C language, realized the functions of initialization, frequency sweep, data sampling, serial port transmission, key processing and result display. Fresh raw milk were used as samples to analyze the relationship between the protein content and the obtained data, i.e., the amplitudes of input and output signals, and the phase difference between the input and output signals. The partial least squares model was established to predict the protein content based on obtained data. The results showed that the model had a determination coefficient of 0.835, the absolute measurement error of -0.11~0.12 g/(100 g), and the average absolute error of 0.01 g/(100 g). Moreover, the measurement could be realized in 2 min. The developed detector made the detection of protein content of fresh raw milk realized quickly and effectively. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 26
Main heading: Signal detection
Controlled terms: C (programming language)? - ?Least squares approximations? - ?Proteins
Uncontrolled terms: Absolute measurements? - ?Average absolute error? - ?Determination coefficients? - ?Development environment? - ?Measurement equipment? - ?Measurement procedures? - ?Partial least squares models? - ?Single chip microcomputers
Classification code: 716.1 Information Theory and Signal Processing? - ?723.1.1 Computer Programming Languages? - ?804.1 Organic Compounds? - ?921.6 Numerical Methods
Numerical data indexing: Frequency 1.00e+06Hz to 1.00e+08Hz, Mass 1.00e-01kg, Time 1.20e+02s
DOI: 10.6041/j.issn.1000-1298.2020.04.045
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
25. Optimization of Management Modes for Intercropping Aeroponics of Lettuce and Cherry Radish
Accession number: 20202008643851
Title of translation:
Authors: Zhang, Lei (1, 2); Li, Faqinwei (1, 2); Yao, Lijun (1, 2); Xiao, Fei (1, 2); Yu, Haiye (1, 2)
Author affiliation: (1) College of Biological and Agricultural Engineering, Jilin University, Changchun; 130022, China; (2) Key Laboratory of Bionic Engineering, Ministry of Education, Jilin University, Changchun; 130022, China
Corresponding author: Yu, Haiye(haiye@jlu.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 337-343
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: High yield and quality of lettuce were objects under the intercropping aeroponics system with cherry radishes. The orthogonal test of three factors and three levels were enforced to reduce nitrate content in edible parts of lettuce under the intercropping aeroponics system. According to a large number of single factor experiments in previous researches, the orthogonal test was utilized to study the influence of intercropping ratio, phased management of nutrient solution concentration and the time of pre-harvest light supplementation on target plants. The results showed that the optimal combination of factors in the cultivation management mode was as follows: the intercropping ratio of lettuce and cherry radish was 2; the nutrient solution was supplied by 0.5 standard concentration in the early stage and in the week before harvest in stages, and standard concentration in the middle stage; and the time of pre-harvest light supplementation was 48 h. High yield, high quality and low nitrate content in the edible parts were found for lettuce in optimal cultivation management mode, which meant that the optimization was obvious. That’s to say, the cultivation management mode provided theoretical basis and reference for the study of soilless cultivation of high quality leafy vegetables with low nitrate. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 34
Main heading: Nitrates
Controlled terms: Harvesting? - ?Nutrients
Uncontrolled terms: Leafy vegetables? - ?Management modes? - ?Nitrate contents? - ?Nutrient solution? - ?Optimal combination? - ?Orthogonal test? - ?Single-factor experiments? - ?Soil-less cultivation
Classification code: 804.2 Inorganic Compounds? - ?821.3 Agricultural Methods
Numerical data indexing: Time 1.73e+05s
DOI: 10.6041/j.issn.1000-1298.2020.04.038
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
26. Energy Control Strategy of Electric Tractor Power Supply Based on Dynamic Programming
Accession number: 20202008643828
Title of translation:
Authors: Li, Yinping (1); Liu, Li (1); Jin, Tianxu (2); Yuan, Kun (1, 3); Chen, Yajue (1)
Author affiliation: (1) School of Mechanical Engineering, University of Science and Technology Beijing, Beijing; 100083, China; (2) Beijing Construction Engineering Research Institute Co., Ltd., Beijing; 100039, China; (3) Beijing Anchises Technologies Co., Ltd., Beijing; 100083, China
Corresponding author: Liu, Li(liliu@ustb.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 403-410
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Aiming to solve the problems of low energy utilization and insufficient cruising range of pure electric tractor, a power supply system of pure electric tractor based on super capacitor and battery composite was proposed. By analyzing the working condition characteristics and power demand of pure electric tractor, the topological structure selection and parameter matching of power supply system were carried out. According to the topology of the composite power system and the operating principle of the battery pack, super capacitor pack and DC/DC, a suitable modeling method was selected to model the battery pack, super capacitor pack and DC/DC by using Simulink, taking the lowest energy consumption of power supply as the optimization objective, the energy control strategy of power supply system of pure electric tractor was optimized by using dynamic programming, and the results of dynamic programming were obtained, and the characteristics of working conditions were analyzed, the energy control strategy of power supply based on rules was summarized, the control strategy was simulated by using Matlab/Simulink model. The results showed that the energy consumption of the control strategy based on dynamic programming was 18% lower than that of the rule-based control strategy, which proved the effectiveness and reliability of the energy control strategy based on dynamic programming in energy saving and consumption reduction. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 26
Main heading: Electric power system control
Controlled terms: Battery Pack? - ?DC-DC converters? - ?Dynamic programming? - ?Energy conservation? - ?Energy utilization? - ?MATLAB? - ?Supercapacitor? - ?Topology? - ?Tractors (agricultural)? - ?Tractors (truck)
Uncontrolled terms: Composite power systems? - ?Control strategies? - ?Energy saving and consumption reductions? - ?Matlab/Simulink modeling? - ?Operating principles? - ?Parameter matching? - ?Rule-based control strategies? - ?Topological structure
Classification code: 525.2 Energy Conservation? - ?525.3 Energy Utilization? - ?663.1 Heavy Duty Motor Vehicles? - ?704.1 Electric Components? - ?706.1 Electric Power Systems? - ?921 Mathematics
Numerical data indexing: Percentage 1.80e+01%
DOI: 10.6041/j.issn.1000-1298.2020.04.047
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
27. Screening Method of Characteristic THz Region to Corn Seed Vigor Based on ATR
Accession number: 20202008643833
Title of translation: ATR
Authors: Wu, Jingzhu (1); Li, Xiaoqi (1); Liu, Cuiling (1); Sun, Xiaorong (1); Yu, Le (1); Sun, Lijuan (2)
Author affiliation: (1) Beijing Key Laboratory of Big Data Technology for Food Safety, Beijing Technology and Business University, Beijing; 100048, China; (2) Institute of Crop Science, Chinese Academy of Agricultural Sciences, Beijing; 100081, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 382-386 and 393
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Characteristic Terahertz (THz) region closely related to corn seed aging were screened by using THz time domain spectroscopy technique and moving window correlation coefficient method. There were three different varieties of corn seeds selected and processed by artificial aging for 0 d, 1 d, 2 d, 3 d and 4 d. The embryos and endosperms of corn seeds samples were isolated and pulverized. THz absorbance spectra (0.2~80 cm-1) of the powder samples were collected by THz time domain system and attenuated total reflection (ATR) accessory. The moving window correlation coefficient method was applied to screen the characteristic spectral regions which were sensitive to seed aging. After comparing the parameters of the moving window correlation coefficient, the window width was determined to 10 and threshold value was 0.3. According to the result, the selected characteristic spectral regions showed significant differences among different varieties of samples, which indicated that the seed aging process was greatly affected by the variety. However, there were minor common regions in the same aging stage which were mainly concentrated in 60~80 cm-1. It was showed that the similar components were changed at the same time. Due to the selected characteristic spectra of endosperm and embryo at the same aging stage were different, it was showed that the endosperm and embryo had different physiological changes during seed aging process. The experiment result indicated that THz time domain spectroscopy combined with chemometric method can be used to characterize and detect the dynamic changes of corn seed aging rapidly and macroscopically. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 25
Main heading: Time domain analysis
Controlled terms: Laser pulses? - ?Reflectometers? - ?Terahertz spectroscopy
Uncontrolled terms: Absorbance spectrum? - ?Attenuated total reflection accessories? - ?Characteristic spectral regions? - ?Chemometric method? - ?Correlation coefficient? - ?Correlation coefficient method? - ?THz time domain spectroscopy? - ?Time domain systems
Classification code: 744.1 Lasers, General? - ?921 Mathematics? - ?931.1 Mechanics? - ?941.3 Optical Instruments
DOI: 10.6041/j.issn.1000-1298.2020.04.044
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
28. Loss Reduction Mechanism and Experiment on Snapping of Rigid-Flexible Coupling Corn Head
Accession number: 20202008644267
Title of translation:
Authors: Fu, Qiankun (1, 2); Fu, Jun (1, 2); Chen, Zhi (2, 3); Ren, Luquan (1, 2)
Author affiliation: (1) Key Laboratory of Bionic Engineering, Ministry of Education, Jilin University, Changchun; 130022, China; (2) College of Biological and Agricultural Engineering, Jilin University, Changchun; 130022, China; (3) Chinese Academy of Agricultural Mechanization Sciences, Beijing; 100083, China
Corresponding author: Fu, Jun(fu_jun@jlu.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 60-68
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: A wheel type rigid-flexible coupling snapping device was designed to reduce kernel loss on corn head. There were two forms of rigid-flexible coupling structure in the device, namely, buffer spring and flexible contacting surface. The buffer spring was fixed to play a cushioning role when the snapping rolls were impacted by corn ear, and the flexible contacting surface was fixed on the snapping rolls to decrease hardness. In order to explore the different roles that two kinds of rigid-flexible coupling structure played in loss reducing of the designed snapping device, impact experiments of corn ear were conducted to study the mechanisms. The experiments were carried out on the widely used corn head with deck plates and the corn head with wheel type rigid-flexible coupling snapping device respectively. Each of the snapping devices was equipped with steel surface and flexible contacting surface composed of silicon rubber. The impact velocity was determined according to the typical working conditions of corn harvester. The impact parameters, including impact time, peak acceleration and impulse as well as the mass of detached kernels were collected. The result showed that buffer spring could shorten the impact time. Compared with snapping device equipped with deck plates, the impact time of corn ear on wheel type rigid-flexible coupling snapping device were shortened by 62.2% and 67.3%, corresponding to steel surface and flexible surface, respectively. Moreover, the impulse was decreased by 60.6% and 76.0%, and the detached kernels mass was decreased by 14.4% and 25.6%. On the other hand, flexible surface could reduce the ear’s impact force by prolonging impact time. Compared with the steel surfaces, impact time of corn head with flexible contacting surfaces were prolonged by 78.4% and 53.8% corresponding to corn head with deck plates and the one with wheel type rigid-flexible coupling snapping devices, respectively, which caused the declines of peak impact force by 45.1% and 55.2%, impulse reduction by 19.9% and 51.2%, respectively, and resulted in a decrease of detached kernel mass by 34.1% and 42.8%. The research can provide theoretical basis for the designs aiming to reduce kernel loss of corn head. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 26
Main heading: Flexible couplings
Controlled terms: Plates (structural components)? - ?Silicon rubber? - ?Wheels
Uncontrolled terms: Contacting surfaces? - ?Flexible surfaces? - ?Impact experiment? - ?Impact velocities? - ?Impact-parameter? - ?Peak acceleration? - ?Peak impact forces? - ?Rigid flexible coupling
Classification code: 408.2 Structural Members and Shapes? - ?601.2 Machine Components? - ?602.2 Mechanical Transmissions
Numerical data indexing: Percentage 1.44e+01%, Percentage 1.99e+01%, Percentage 2.56e+01%, Percentage 3.41e+01%, Percentage 4.28e+01%, Percentage 4.51e+01%, Percentage 5.12e+01%, Percentage 5.38e+01%, Percentage 5.52e+01%, Percentage 6.06e+01%, Percentage 6.22e+01%, Percentage 6.73e+01%, Percentage 7.60e+01%, Percentage 7.84e+01%
DOI: 10.6041/j.issn.1000-1298.2020.04.007
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
29. Design and Experiment of Small Cooling Storage Vacuum Precooling Device for Fresh Wolfberry with Stem
Accession number: 20202008643831
Title of translation:
Authors: Deng, Gaige (1, 2); Kang, Ningbo (1); Wang, Songlei (1, 3); Liu, Guishan (3); He, Jianguo (1, 3)
Author affiliation: (1) School of Civil Engineering and Hydraulic Engineering, Ningxia University, Yinchuan; 750021, China; (2) School of Information Engineering, China University of Mining and Technology Yinchuan College, Yinchuan; 750021, China; (3) School of Agriculture, Ningxia University, Yinchuan; 750021, China
Corresponding author: He, Jianguo(hejg@nxu.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 367-372 and 381
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: At present, the vacuum pre-cooling device has a large volume, high energy consumption, and the water catching capacity of the water trap can not be well adapted to the problem of evaporation of water vapor. In order to solve the above problems, a small-scale wolfberry vacuum precooling device based on brine storage was designed. According to the technical requirements, the mathematical model of vacuum precooling was established. The theoretical analysis of the surface mass transfer resistance layer was carried out. The key parameters of the vacuum pump, vacuum precooling and cooling load, brine storage system and computer detection system were designed and calculated. Finally, a small cooling storage vacuum precooling device for fresh wolfberry with stem was produced. The experimental results showed that the vacuum precooling device can reduce the center temperature of 8.714 kg fresh wolfberry to the preservation temperature of 4.0 in 879 s, and the water loss rate was 5.29% when the water replenishment rate was 4.50%. The water trap of the device was designed to have a water catch rate of 75.00%, and the actual water catch rate was 79.32%. The brine temperature in the brine tank was increased from -20.1 to -9.8 during the test. The cold storage capacity of the brine in the tank can ensure the smooth completion of the vacuum pre-cooling process. By adjusting the brine pump to change the brine circulation speed, the balance between the catchment of the water trap and the evaporation of water vapor was achieved, which met the design requirements. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 22
Main heading: Cooling
Controlled terms: Catchments? - ?Cold storage? - ?Energy utilization? - ?Mass transfer? - ?Tanks (containers)? - ?Vacuum evaporation? - ?Water vapor
Uncontrolled terms: Brine circulation? - ?Detection system? - ?High energy consumption? - ?Storage capacity? - ?Surface mass transfers? - ?Technical requirement? - ?Vacuum precooling? - ?Water loss rates
Classification code: 525.3 Energy Utilization? - ?619.2 Tanks? - ?633.1 Vacuum Applications? - ?641.2 Heat Transfer? - ?641.3 Mass Transfer? - ?644.3 Refrigeration Equipment and Components
Numerical data indexing: Mass 8.71e+00kg, Percentage 4.50e+00%, Percentage 5.29e+00%, Percentage 7.50e+01%, Percentage 7.93e+01%, Time 8.79e+02s
DOI: 10.6041/j.issn.1000-1298.2020.04.042
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
30. Fruit Tree Canopy Image Segmentation Method Based on M-LP Features Weighted Clustering
Accession number: 20202008643845
Title of translation: M-LP
Authors: Cheng, Zhenzhen (1); Qi, Lijun (1); Cheng, Yifan (2); Wu, Yalei (1); Zhang, Hao (1); Xiao, Yu (1)
Author affiliation: (1) College of Engineering, China Agricultural University, Beijing; 100083, China; (2) Beijing Siweitu New Technology Co., Ltd., Beijing; 100094, China
Corresponding author: Qi, Lijun(qilijun@cau.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 191-198 and 260
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Fruit canopy information collection plays an important role in the orchard variable spray. Aiming at the problem of canopy extraction of fruit trees under background (non-green plants) and weed disturbance, a canopy segmentation algorithm was proposed based on M-SP feature weighted clustering. The segmentation process can be described as: the original image was converted from RGB color space to HSI color space. The Mahalanobis distance similarity matrix (M) was constructed by calculating the hue (H) and saturation (S) components between fruit tree and the background; moreover, luminance feature (L) was extracted: the vertical position of the pixel was used as the position feature (P). The maximum entropy algorithm was used to extract the shadow region of the image and perform mask processing on the intensity (I) component in the HSI. The obtained shadow region was used as weighted region S of spatial feature, thereby constructing the shadow position weighting. Finally, the acquired M-SP feature matrix was normalized, and the K-means clustering of the upper background, the lower background, the fruit canopy and the weeds were respectively performed, and the image segmentation was finally completed. In order to verify the accuracy of the quantitative verification algorithm, precision, recall and F1-scores were used to evaluate the image segmentation results under different weed disturbance levels (slight, medium and strong) and time segments (morning, noon and evening). The K-means and Gaussian mixture model (GMM) without feature extraction were used respectively as comparative experiments. The results showed that the proposed method was robust to the canopy segmentation of fruit trees under different weed interference levels and different shooting time periods. The average precision was 87.1%, the average recall was 87.7%, and the average F1-scores was 87.1%. The segmentation and verification results showed that the algorithm can accurately segment the canopy area of fruit trees, which provided a reference for collecting the canopy information of fruit trees by computer vision. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 25
Main heading: Image segmentation
Controlled terms: Color? - ?Extraction? - ?Fruits? - ?Gaussian distribution? - ?K-means clustering? - ?Orchards? - ?Trees (mathematics)
Uncontrolled terms: Comparative experiments? - ?Gaussian Mixture Model? - ?Information collections? - ?Mahalanobis distances? - ?Maximum entropy algorithms? - ?Quantitative verification? - ?Segmentation algorithms? - ?Segmentation methods
Classification code: 741.1 Light/Optics? - ?802.3 Chemical Operations? - ?821.3 Agricultural Methods? - ?821.4 Agricultural Products? - ?921.4 Combinatorial Mathematics, Includes Graph Theory, Set Theory? - ?922.1 Probability Theory
Numerical data indexing: Percentage 8.71e+01%, Percentage 8.77e+01%
DOI: 10.6041/j.issn.1000-1298.2020.04.022
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
31. Design and Test of SYJ-3 Deep Application-type Inclined Liquid Fertilizer Hole Applicator
Accession number: 20202008644270
Title of translation: SYJ-3
Authors: Zhou, Wenqi (1); Xiao, Hong (2); Liu, Ziming (1); Wang, Jinwu (1); Huang, Huinan (1); Wang, Aoxue (3)
Author affiliation: (1) College of Engineering, Northeast Agricultural University, Harbin; 150030, China; (2) Heilongjiang Institute of Agricultural Mechanical Engineering Science, Harbin; 150081, China; (3) School of Horticulture and Landscape Architecture, Northeast Agricultural University, Harbin; 150030, China
Corresponding author: Wang, Aoxue(axwang@neau.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 78-86
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Considering the problems, namely crops damage, large hole width and low fertilizer spraying efficiency of deep application-type liquid fertilizer hole applicator, a deep application-type inclined liquid fertilizer hole applicator was designed. Through the design of “oblique hole pricking and parameter reverse solution”, and based on the human-computer interaction platform, the pricking hole mechanism of key components was designed, the structure and working parameters of the mechanism were optimized, and the movement form of fertilizer feeding interface of fertilizer spraying needle was analyzed. According to the technical characteristics of spraying fertilizer needle earthing and unearthing fertilizer, and to improve the efficiency of fertilizer delivery, the liquid fertilizer distribution mechanism, which was the key component, was designed by using the combined transmission form of “differential gear train transmission and space cam mechanism”. The movement model of the fertilizer outlet interface was constructed to analyze and satisfy the cooperative movement mechanism with the fertilizer inlet interface and reduce the complicated connection configuration of the fertilizer delivery pipeline. The field performance test of the deep application-type inclined liquid fertilizer hole applicator revealed a superior hole punching performance, the fertilizer was sprayed evenly, and the mechanical damage to crops was small. The hole width, crop damage rate, fertilization amount and fertilization depth were 45.0 mm, 0.3%, 28.5 mL/time and 102 mm, respectively. All indexes were less different from the previous design and met the agronomic requirements. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 25
Main heading: Fertilizers
Controlled terms: Applicators? - ?Crops? - ?Efficiency? - ?Human computer interaction? - ?Liquids? - ?Needles? - ?Transmissions
Uncontrolled terms: Cooperative movement? - ?Differential gear trains? - ?Distribution mechanism? - ?Field performance? - ?Liquid fertilizers? - ?Mechanical damages? - ?Spraying fertilizers? - ?Structure and working parameters
Classification code: 601 Mechanical Design? - ?602.2 Mechanical Transmissions? - ?804 Chemical Products Generally? - ?821.4 Agricultural Products? - ?913.1 Production Engineering
Numerical data indexing: Percentage 3.00e-01%, Size 1.02e-01m, Size 4.50e-02m
DOI: 10.6041/j.issn.1000-1298.2020.04.009
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
32. Distribution Model of Wind-stressed Droplet Deposition Based on Bimodal Distribution
Accession number: 20202008643848
Title of translation:
Authors: Liang, Zhao (1); Fan, Guoqiang (1, 2); Wang, Guangming (1, 3); Ding, Hao (1); Zhang, Xiaohui (1, 2)
Author affiliation: (1) College of Mechanical and Electrical Engineering, Shandong Agricultural University, Tai’an; 271018, China; (2) Shandong Provincial Intelligent Engineering Laboratory of Agricultural Equipment, Shandong Agricultural University, Tai’an; 271018, China; (3) Shandong Provincial Key Laboratory of Horticultural Machineries and Equipments, Shandong Agricultural University, Tai’an; 271018, China
Corresponding author: Zhang, Xiaohui(zhangxh@sdau.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 28-37
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Because of wind stress, the movement trajectory of fog droplet in space was changed, and the deposition distribution of fog droplets on the target surface was changed. In order to study the effect of different factors on this phenomenon, a test of droplet deposition distribution in closed silo was designed. The variables were the transverse wind at different speeds (1 m/s, 2 m/s and 3 m/s), spray height (30 cm, 40 cm and 50 cm) and spray pressure (0.4 MPa, 0.6 MPa and 0.8 MPa). Based on the experimental measurement results of deposition distribution, a bimodal distribution mathematical model based on normal distribution probability density function was established. The physical significance of each coefficient in the model was also explained, and the influence of various horizontal factors on the coefficients in bimodal distribution and influence relationship of each horizontal factor on the coefficient in bimodal distribution were analyzed. This mathematical model can more systematically express the relationship between deposition range and deposition quality. The variation law of deposition parameter k1 was opposite to k2. With the increase of spray height, spray pressure and cross wind speed, k1 was decreased while k2 was increased, and deposition shifted from the first peak distribution to the second peak distribution. The two position parameters μ1 and μ2 of the bimodal distribution had the same variation trend, both increasing with the increase of wind speed and height, and decreasing with the increase of spray pressure. Therefore, increasing the spray pressure can reduce the center drift distance. The range of the first and second peak distributions (scale parameters σ1 and σ2) were increased with the increase of spray height and wind speed, and the deposition distribution was more dispersed. Increasing the spray pressure can effectively reduce the deposition dispersion of the first peak, but it had no effect on the distribution of the second peak. This study investigated the effects of different intensity of transverse wind and spray height and pressure on droplet drift deposition distribution, providing a reference for optimizing pesticide spray technology and improved droplet resistance to drift. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 30
Main heading: Deposition
Controlled terms: Drops? - ?Normal distribution? - ?Probability density function? - ?Wind
Uncontrolled terms: Bimodal distribution? - ?Deposition distribution? - ?Deposition Parameters? - ?Distribution probability? - ?Influence relationships? - ?Movement trajectories? - ?Physical significance? - ?Position parameters
Classification code: 443.1 Atmospheric Properties? - ?802.3 Chemical Operations? - ?922.1 Probability Theory
Numerical data indexing: Pressure 4.00e+05Pa, Pressure 6.00e+05Pa, Pressure 8.00e+05Pa, Size 3.00e-01m, Size 4.00e-01m, Size 5.00e-01m, Velocity 1.00e+00m/s, Velocity 2.00e+00m/s, Velocity 3.00e+00m/s
DOI: 10.6041/j.issn.1000-1298.2020.04.003
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
33. Accuracy of Photon Cloud Noise Filtering Algorithm in Forest Area under Weak Beam Conditions
Accession number: 20202008644207
Title of translation:
Authors: Huang, Jiapeng (1); Xing, Yanqiu (1); Qin, Lei (1); Ma, Jianming (1)
Author affiliation: (1) Centre for Forest Operations and Environment, Northeast Forestry University, Harbin; 150040, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 164-172
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Advanced topographic laser altimeter system (ATLAS) can provide scientific data for global canopy height measurement. However, due to the characteristics of background noise in the photon data, the traditional algorithm does not study for the forest coverage area under weak beam conditions and there was still few photon cloud noise filtering algorithm can evaluate the accuracy of noise filtering under the condition of weak beam in forest research area. In order to quantify the accuracy of the photon cloud noise filtering algorithm in the forest research area under the condition of weak beam, the accuracies of the local distance statistical algorithm, the density-based spatial clustering of applications with noise (DBSCAN) algorithm and the particle swarm optimization (PSO)-DBSCAN algorithm for photon cloud noise filtering experiments in forest areas under weak beam conditions were studied, and the influence of different characteristics on noise filtering results was analyzed. The results were as follows: the results showed that PSO-DBSCAN algorithm had the accuracy of noise filtering as 0.95 in the forest area under weak beam conditions, which met the accuracy of photon cloud noise filtering requirements, and the algorithm performed better than the local distance statistical algorithm and the DBSCAN algorithm. The solar elevation angle had greater impact on the noise filtering algorithm than the terrain slope and vegetation coverage. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 25
Main heading: Clustering algorithms
Controlled terms: Aneroid altimeters? - ?Forestry? - ?Particle swarm optimization (PSO)? - ?Photons? - ?Radio altimeters? - ?Signal filtering and prediction? - ?Spurious signal noise
Uncontrolled terms: Background noise? - ?DBSCAN algorithm? - ?Density-based spatial clustering of applications with noise? - ?Forest research? - ?Laser altimeter? - ?Scientific data? - ?Statistical algorithm? - ?Vegetation coverage
Classification code: 716.1 Information Theory and Signal Processing? - ?716.3 Radio Systems and Equipment? - ?723 Computer Software, Data Handling and Applications? - ?903.1 Information Sources and Analysis? - ?931.3 Atomic and Molecular Physics? - ?944.3 Pressure Measuring Instruments
DOI: 10.6041/j.issn.1000-1298.2020.04.019
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
34. Establishment of Photosynthetic Rate Prediction Model for Eggplant Leaves Fused with Dark Fluorescence Parameters
Accession number: 20202008644246
Title of translation:
Authors: Hu, Jin (1, 2); Gao, Pan (1, 2); Chen, Danyan (1, 2); Li, Bin (1, 3); Jin, Haonan (1); Zhang, Haihui (1, 3)
Author affiliation: (1) College of Mechanical and Electronic Engineering, Northwest A&F University, Yangling; Shaanxi; 712100, China; (2) Key Laboratory of Agricultural Internet of Things, Ministry of Agriculture and Rural Affairs, Yangling; Shaanxi; 712100, China; (3) Shaanxi Key Laboratory of Agricultural Information Perception and Intelligent Services, Yangling; Shaanxi; 712100, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 328-336
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: The photosynthetic models now mainly consider the effects of environmental factors on plant photosynthesis. These models can only predict photosynthetic rate of leaves with similar physiological conditions. In order to meet the needs of modeling the models for leaf photosynthetic rate prediction in different growth states, a method for constructing a multi-environmental factors photosynthetic rate prediction model incorporating dark fluorescence parameters Fv/Fm was proposed. Taking eggplant leaves of different growth states as samples, the Fv/Fm were obtained, and the photosynthetic rates were measured at different temperatures, CO2 concentrations and light intensities to construct a set of modeling samples. Then a unified prediction model of photosynthetic rate was established by using genetic support vector regression. The determinant coefficient of the model was 0.889 5, and the root mean square error was 3.267 9 μmol/(m2?s). The results of XOR checkout showed that the accuracy of the model was improved remarkably by fusing the Fv/Fm. The fitting slope between the predicted and measured photosynthetic rates was 0.904 6, the intercept was 0.364 1, which showed that the model could predict an exact photosynthetic rate of leaves with different physiological conditions by leading in Fv/Fm. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 37
Main heading: Physiological models
Controlled terms: Fluorescence? - ?Forecasting? - ?Mean square error? - ?Physiology? - ?Plants (botany)? - ?Support vector regression
Uncontrolled terms: CO2 concentration? - ?Environmental factors? - ?Fluorescence parameters? - ?Genetic support vector regressions? - ?Photosynthetic model? - ?Photosynthetic rate? - ?Physiological condition? - ?Root mean square errors
Classification code: 461.9 Biology? - ?741.1 Light/Optics? - ?922.2 Mathematical Statistics
DOI: 10.6041/j.issn.1000-1298.2020.04.037
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
35. Moisture and Heat Characteristics and Apparent Form of Balsam Pears in Microwave-Hot-airflow Vibrating Bed Drying
Accession number: 20202008644279
Title of translation: -
Authors: Lü, Hao (1); Lü, Huangzhen (2); Yang, Bingnan (2); Lü, Weiqiao (1); Du, Zhilong (2)
Author affiliation: (1) College of Engineering, China Agricultural University, Beijing; 100083, China; (2) Chinese Academy of Agricultural Mechanization Sciences, Beijing; 100083, China
Corresponding author: Lü, Weiqiao(lvweiqiao@cau.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 373-381
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Aiming to explore the effect of wet-thermal characteristics and morphology of hot-airflow on the microwave vibrating fluidized bed drying, the drying kinetics,thermal image changes,water distribution,color and microstructure of fresh bitter gourd slices under four microwave-hot-airflow drying modes were studied by microwave-hot-airflow vibrating dryer. The results showed that the hot-airflow temperature had a significant effect on microwave-hot-airflow vibrating fluidized bed drying. The drying time of hot-airflow drying was slower, and the drying time of microwave drying alone, microwave power 0.6 W/g+hot-airflow 60+ air-speed 3 m/s, microwave power 0.6 W/g+hot-airflow 70+ air-speed 6 m/s was 56.4%,70.5% and 75.6% shorter than that of the hot-airflow drying with hot air 70+air-speed 3 m/s. The color of dehydrated product by hot-airflow was closest to fresh balsam pear slices, the color of dehydrated product by microwave-hot-airflow combination drying was better than that of microwave drying alone. The temperature uniformity of microwave-hot-airflow combination drying was significantly better than that of microwave drying alone and hot-airflow drying alone. The moisture signal was gradually decreased and the main peak was moved to the left under NMR spectrum by four drying modes. The MRI signal showed that hot-airflow had a significant effect on the uniformity of water distribution during microwave drying. Scanning electron microscopy observation showed that the hot-airflow drying was the most obvious to maintain the cell integrity of dehydrated product, and the cell integrity of microwave-hot-airflow drying was better than that of microwave alone. The study provided a theoretical basis for the processing technology selection of dehydrated product. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 20
Main heading: Drying
Controlled terms: Color? - ?Fluidized bed process? - ?Fluidized beds? - ?Fruits? - ?Microwave generation? - ?Microwave heating? - ?Moisture? - ?Morphology? - ?Nuclear magnetic resonance spectroscopy? - ?Scanning electron microscopy ? - ?Signal systems? - ?Water supply systems
Uncontrolled terms: Combination drying? - ?Dehydrated products? - ?Fluidized bed drying? - ?Heat characteristics? - ?Processing technologies? - ?Temperature uniformity? - ?Thermal characteristics? - ?Water distributions
Classification code: 446.1 Water Supply Systems? - ?642.1 Process Heating? - ?713.2 Oscillators? - ?741.1 Light/Optics? - ?821.4 Agricultural Products? - ?951 Materials Science
Numerical data indexing: Percentage 5.64e+01%, Percentage 7.56e+01%, Velocity 3.00e+00m/s, Velocity 6.00e+00m/s
DOI: 10.6041/j.issn.1000-1298.2020.04.043
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
36. Mechanism of Wheel-Ground Crossed Friction Wheel Drive and Application in Motion Analysis of Omni-directional Mobile Car
Accession number: 20202008644253
Title of translation:
Authors: Jiang, Song (1); Chen, Qiying (1); Feng, Kan (2); Chen, Zhangyao (2); Liu, Wei (1); Jiang, Yiyi (1)
Author affiliation: (1) School of Food and Biological Engineering, Jiangsu University, Zhenjiang; 212013, China; (2) Faculty of Civil Engineering and Mechanics, Jiangsu University, Zhenjiang; 212013, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 394-402
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Aiming to clarify the transmission relationship of the crossed friction wheel mechanism and apply it to the motion analysis of the Mecanum wheeled omni-directional mobile car, the transmission principle was theoretically analyzed through motion analysis and force analysis. The theoretical relationship and the design calculation method of dynamic parameters of a special case of the crossed friction drive about wheel-ground crossed friction wheel drive were analyzed. The method for judging the axial movement direction of the driven transmission member was constructed. The ADAMS was used to simulate the transmission model of crossed friction wheel under different loading conditions. On this basis, the motion principle of the omni-directional mobile car based on the Mecanum wheel was analyzed by using the mechanism of the crossed friction wheel transmission. The research result showed that the theoretical analysis of the transmission relationship was correct. When the transmission was effective, the angle between the static friction force of the contact point and the axis of the wheel was depended on the applied load value. The static friction of the contact point and the applied load could be adaptively balanced. The relationship between the moving speed of the wheel center and the axial moving speed along the shaft and the driving speed of the supporting shaft was not affected by the external load. These three speeds formed a right-angled triangle relationship, and the two speeds of the friction wheel were the cosine and sine of the driving speed. The transmission relationship between the ground and the small rollers of the Mecanum wheel belonged to the crossed friction wheel drive. It was feasible to analyze the omni-directional mobile car by using theoretical movement relationship of the crossed friction wheel. It provided an intuitive and concise theoretical method for the analysis of the omni-directional mobile car based on Mecanum wheel, and also provided a theoretical basis for the application design and analysis of the crossed friction wheel drive. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 27
Main heading: Wheels
Controlled terms: Motion analysis? - ?Speed? - ?Stiction? - ?Transmissions
Uncontrolled terms: Design calculations? - ?Dynamic parameters? - ?Movement relationship? - ?Omni-directional mobiles? - ?Static friction force? - ?Theoretical methods? - ?Transmission model? - ?Transmission principle
Classification code: 601.2 Machine Components? - ?602.2 Mechanical Transmissions? - ?723.2 Data Processing and Image Processing
DOI: 10.6041/j.issn.1000-1298.2020.04.046
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
37. Biomimetic Design and Experiment of Core-share Furrow Opener
Accession number: 20202008644195
Title of translation:
Authors: Jia, Honglei (1, 2); Meng, Fanhao (1); Liu, Lijing (3); Shi, Song (4); Zhao, Jiale (1, 2); Zhuang, Jian (1, 2)
Author affiliation: (1) College of Biological and Agricultural Engineering, Jilin University, Changchun; 130022, China; (2) Key Laboratory of Bionic Engineering, Ministry of Education, Changchun; 130022, China; (3) Chinese Academy of Agricultural Mechanization Sciences, Beijing; 100083, China; (4) Shandong Academy of Agricultural Machinery Sciences, Ji’nan; 250100, China
Corresponding author: Zhuang, Jian(zhuangjian_2001@163.com)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 44-49 and 77
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: In view of the problem that the resistance of the core-share furrow opener is too large under high speed operation, an optimal design method of furrow opener based on the bionics principle was proposed based on the efficient and low resistance penetration structure of the dog-badger canine tooth surface. China northeast farmed badger was selected as bionic biological samples, it was carried out on the upper right canine of badger advance disinfection after treatment for 3D scanning and obtained the complete point cloud data, and then through the Matlab software, fitting curve of the four best badger canine based on the above four design was obtained and the four kinds of slide furrowing device were processed, finally it was compared with the traditional core-share furrow opener through contrast test analysis. Under the condition that the operating depth was 50 mm, the type of opening device and operating speed were taken as the test factors, the horizontal operating resistance was taken as the main index, and the trench depth, trench width, ridge height and ridge width of the trench device were taken as the secondary index to conduct the soil groove test. The experimental results showed that the resistance of each optimized sliding trench opener was lower than that of the standard core-share furrow opener at the same operating speed. At operating speed of 3.6 km/h, 5.4 km/h and 7.2 km/h, the operating resistance of the optimal sliding trench device can be reduced by up to 8.04%, 8.15% and 8.71%, respectively, compared with the standard core-share furrow opener. The variation coefficient of furrow depth, furrow width, side ridge height and side ridge width by standard core-share furrow openers and optimized sliding furrow openers were all lower than 5%. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 25
Main heading: Design
Controlled terms: Biomimetics? - ?Bionics? - ?Curve fitting? - ?MATLAB? - ?Software testing
Uncontrolled terms: Biological samples? - ?Biomimetic design? - ?Bionics principles? - ?High-speed operation? - ?Matlab- software? - ?Optimal design methods? - ?Point cloud data? - ?Variation coefficient
Classification code: 461 Bioengineering and Biology? - ?723.5 Computer Applications? - ?921.6 Numerical Methods
Numerical data indexing: Percentage 5.00e+00%, Percentage 8.04e+00%, Percentage 8.15e+00%, Percentage 8.71e+00%, Size 5.00e-02m, Velocity 1.00e+00m/s, Velocity 1.50e+00m/s, Velocity 2.00e+00m/s
DOI: 10.6041/j.issn.1000-1298.2020.04.005
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
38. Simulation Analysis and Test of Interaction between Pricking Hole Needle Body of Liquid Fertilizer Hole Applicator and Soil
Accession number: 20202008644282
Title of translation:
Authors: Zhou, Wenqi (1); Sun, Xiaobo (1); Liu, Ziming (1); Qi, Xin (1); Jiang, Dongxuan (1); Wang, Jinwu (1)
Author affiliation: (1) College of Engineering, Northeast Agricultural University, Harbin; 150030, China
Corresponding author: Wang, Jinwu(jinwuw@163.com)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 87-94
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Aiming at the problem that it is difficult to directly obtain the three-dimensional resistance variation law and soil dynamic behavior characteristics of the soil contact component-needle body through experiments when the liquid fertilizer hole applicator is pricked with the inclined pricking hole mechanism. By adopting the Drucker-Prager yield criterion to construct the finite element model of hole application soil, the ADAMS kinematics analysis module was applied to obtain the pricking hole track of fertilizer spraying needle of pricking hole mechanism, and ANSYS/LS-DYNA display dynamics software was used to establish the interaction simulation model between fertilizer spraying needle and soil. Taking the maximum pressure on the needle body in the Z-axis direction as the measurement index and the working parameters as the influencing factors, the virtual and bench comparative tests of single way stress on the fertilizer spraying needle were carried out. The results revealed that the pressure was increased first and then decreased with the increase of the advancing speed and the rotation of puncture speed. The simulation and test data were close in size and the change trend was basically the same. Taking the advance speed of the fertilizer spraying needle (0.62 m/s), the rotation speed of the puncture hole (70 r/min) and the inclined angle (20°) as the simulation working parameters, the three-dimensional resistance of the needle body and the dynamic behavior of the soil were simulated and analyzed. The analysis disclosed that the resistance of the fertilizer spraying needle in the three directions was increased first and then decreased. Within 0~0.189 s, the process of the fertilizer spraying needle entering the soil, the resistance of the needle body was changed slowly in the X-axis direction, indicating that the fertilizer spraying disturbed less to the soil in the advancing direction. The resistance of the needle body was increased rapidly in the Z-axis direction, which indicated that the fertilizer spraying needle had a strong impact on the soil. The stress of the soil was mainly concentrated in this direction due to the shear of the needle tip, and the resistance reached the maximum value of 21.69 N at 0.189 s. The resistance of the needle body in the Y-axis direction was small, which indicated that the squeezing effect of the fertilizer spraying needle on the soil was weak, and the resistance reached the maximum value of 8.56 N at 0.189 s. Within 0.189~0.214 s, the original position of the fertilizer spraying needle swung itself, the resistance of the needle body was increased rapidly in the X-axis direction, which indicated that fertilizer spraying needle triggered great disturbance to the soil in the advancing direction. The resistance values in the other two directions remained basically unchanged. Within 0.214~0.350 s, the excavation of the fertilizer spraying needle, the resistance of the needle in the Z-axis and Y-axis directions were gradually decreased until it became zero. Among them, within 0.214~0.238 s, the resistance of the needle body in the X-axis direction was increased instantly, indicating that fertilizer spraying produced strong extrusion on the soil in the forward direction, reaching the maximum value of 31.87 N at 0.238 s. During the whole pricking process, the formation of the puncture opening was mainly caused by the swing posture of the fertilizer spraying needle itself and the soil disturbance in the forward direction during the excavation process. Therefore, the resistance of the needle body along the X-axis direction was influenced significantly, which conformed to the actual pricking hole law. The simulation method of needle-soil interaction provided can be a reference for the optimization design of fertilizer spraying needle and the research of clay characteristics. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 25
Main heading: Needles
Controlled terms: Application programs? - ?Applicators? - ?Excavation? - ?Fertilizers? - ?Rotation? - ?Shear flow? - ?Soil mechanics? - ?Soils
Uncontrolled terms: Drucker Prager yield criterion? - ?Excavation process? - ?Interaction simulations? - ?Kinematics analysis? - ?Optimization design? - ?Resistance variations? - ?Simulation analysis? - ?Working parameters
Classification code: 483.1 Soils and Soil Mechanics? - ?601 Mechanical Design? - ?631.1 Fluid Flow, General? - ?723 Computer Software, Data Handling and Applications? - ?804 Chemical Products Generally? - ?931.1 Mechanics
Numerical data indexing: Force 2.17e+01N, Force 3.19e+01N, Force 8.56e+00N, Rotational_Speed 7.00e+01RPM, Time 0.00e+00s to 1.89e-01s, Time 1.89e-01s, Time 1.89e-01s to 2.14e-01s, Time 2.14e-01s to 2.38e-01s, Time 2.14e-01s to 3.50e-01s, Time 2.38e-01s, Velocity 6.20e-01m/s
DOI: 10.6041/j.issn.1000-1298.2020.04.010
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
39. Design and Experiment of Transplanting Device with Variable Row-spacing of Rice Potted-seedling Transplanter
Accession number: 20202008643860
Title of translation:
Authors: Cai, Jinping (1, 2); Liu, Muhua (1, 2); Xiao, Liping (1, 2); Lin, Jinlong (1, 2); Ye, Yangyang (1); Yang, Hongfei (1)
Author affiliation: (1) College of Engineering, Jiangxi Agricultural University, Nanchang; 330045, China; (2) Jiangxi Key Laboratory of Modern Agricultural Equipment, Nanchang; 330045, China
Corresponding author: Xiao, Liping(applexlp42@163.com)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 50-59
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: As the existing rice pot seedling transplanter with fixed row-spacing failed to meet the agronomic requirements of rice transplanting with different row-spaces in the double cropping rice area in south China,a kind of pot seedling transplanting device gearing to the need of variable row-spacing transplanting was accordingly designed based on the existing walking type rice transplanter. Firstly,the optimal pulling angle of pot seedlings and the location of picking and falling determined the trajectory of pot seedlings,and the kinematics model of connecting rod mechanism of picking seedlings was established, the design of the mechanism model was optimized with the help of Matlab. Secondly,according to the motion parameters of the connecting rod mechanism and the motion requirements of the clamping motion posed by the dropping posture of the pot seedling when it was being thrown,the CAM of the clamping motion control was designed,and the motion simulation was carried out to analyze the synchronism of the movement between the connecting rod mechanism and the clamping motion. Then,in order to maintain the consistency of the time when the pot seedlings fell into the paddy field after passing through the transmission tube to ensure the uniform plant spacing during transplanting,the wall inclination angle of the key parameters of the transmission tube was theoretically analyzed and designed. Finally,transplanting experiments were carried out with different seedling speeds and row-spacings,and the average successful rate of seedling extraction reached 89.96% and the average inverted seedling rate was 3.45%,indicating that the device had a good transplanting effect and could be applied to the transplanting of rice pot seedlings with variable row-spacing. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 25
Main heading: Seed
Controlled terms: Agricultural machinery? - ?Connecting rods? - ?MATLAB? - ?Transmissions
Uncontrolled terms: Inclination angles? - ?Kinematics modeling? - ?Motion simulations? - ?Pot seedling transplanters? - ?Rice potted seedling? - ?Rice transplanter? - ?Seedling transplanting? - ?Transplanting devices
Classification code: 602.2 Mechanical Transmissions? - ?821.1 Agricultural Machinery and Equipment? - ?821.4 Agricultural Products? - ?921 Mathematics
Numerical data indexing: Percentage 3.45e+00%, Percentage 9.00e+01%
DOI: 10.6041/j.issn.1000-1298.2020.04.006
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
40. Research Progress of Agricultural Machinery Navigation Technology
Accession number: 20202008643864
Title of translation:
Authors: Zhang, Man (1); Ji, Yuhan (1); Li, Shichao (1); Cao, Ruyue (1); Xu, Hongzhen (1); Zhang, Zhenqian (1)
Author affiliation: (1) Key Laboratory of Modern Precision Agriculture System Integration Research, Ministry of Education, China Agricultural University, Beijing; 100083, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 1-18
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: The automatic navigation technology of agricultural machinery is the basis for the implementation of precision agriculture, which can effectively reduce the labor intensity of agricultural machinery operators, improve the operation accuracy and efficiency. The classic automatic navigation of agricultural machinery includes three key technologies: positioning and attitude measurement, path planning and motion control. Based on the global navigation satellite system, the inertial navigation system, the machine vision navigation system and the multi-sensor data fusion algorithms, the methods of agricultural machinery positioning and attitude measurement were introduced firstly, and then the global path and local path planning algorithms in the agricultural machinery automatic navigation system were summarized, and the kinematic models, control methods and actuators for steering and braking were analyzed on agricultural machinery. With the development of information technology, the intelligent navigation technology of agricultural machinery had attracted more and more attention. Ensuring the safety of operation and improving the efficiency of cooperation were the key technologies of intelligent navigation of agricultural machinery different from traditional automatic navigation. LiDAR and RGB camera were taking as examples, the autonomous obstacle avoidance technology of agricultural machinery was analyzed, and the cooperative operation technology of multiple agricultural machinery was expounded, including cooperative mode, the perspectives of communication technology, cooperative controlling and remote management platform respectively. Finally, the future development direction of intelligent navigation technology for agricultural machinery was prospected with the specific example of “Hands Free Hectare” and smart agriculture. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 127
Main heading: Visual servoing
Controlled terms: Agricultural machinery? - ?Agricultural robots? - ?Agriculture? - ?Collision avoidance? - ?Cooperative communication? - ?Efficiency? - ?Inertial navigation systems? - ?Kinematics? - ?Motion planning? - ?Sensor data fusion
Uncontrolled terms: Automatic navigation systems? - ?Autonomous obstacle avoidances? - ?Communication technologies? - ?Cooperative operation? - ?Development directions? - ?Global Navigation Satellite Systems? - ?Intelligent navigation? - ?Multisensor data fusion
Classification code: 722.3 Data Communication, Equipment and Techniques? - ?723.2 Data Processing and Image Processing? - ?821 Agricultural Equipment and Methods; Vegetation and Pest Control? - ?821.1 Agricultural Machinery and Equipment? - ?913.1 Production Engineering? - ?914.1 Accidents and Accident Prevention? - ?931.1 Mechanics
DOI: 10.6041/j.issn.1000-1298.2020.04.001
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
41. Experiments and Design on Single-rolled Seed-sowing System of Pre-seed-cutting Sugarcane Planters with Wide and Narrow Row Spacing
Accession number: 20202008644131
Title of translation:
Authors: Li, Shangping (1, 2); Huang, Zongxiao (1); Zhang, Wei (1); Xiang, Rui (1); Wang, Mengping (1); Mo, Hanning (1)
Author affiliation: (1) College of Mechanical Engineering, Guangxi University, Nanning; 530004, China; (2) College of Information Science and Engineering, Guangxi University for Nationalities, Nanning; 530006, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 113-121
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Aimed at problems that currently nonuniform seed sowing, low pass rate, high seed missing rate, great seed wasting and severe seed blocking existed in the seed-sowing system of pre-seed-cutting sugarcane planters with wide and narrow row spacing, virtual experiment analysis and practical experiment research were conducted through ADAMS. A kind of pre-seed-cutting seed-sowing systems with a single roll bottom sowing edge were designed and developed. The effects of the parameters as the rotation velocity of seed-sowing roll, lateral plate angle, flow-controlling plate elastic structure of the sugarcane-gathering box of the seed-sowing device and ordered rotating sugarcane gathering on seed sowing properties were studied through the test platform. The following results were turned out according to experiment results: the qualified rate of automatic rotating ordered flow guiding sugarcane gathering was 95.1%, the flow-controlling plate elastic structure of the sugarcane-gathering box of the seed-sowing device had significant effects on pass rate of seed sowing, the lateral plate angle and the rotation velocity of seed-sowing rolls had generally significant effects. Optimized parameters of the seed-sowing device were as follows: using the flow-controlling plate elastic structure, the lateral plate angle of the sugarcane-gathering box was 105°, the rotation velocity of seed-sowing rolls was 6 r/min (the theoretical seed sowing velocity was 0.83 s/stick). Finally, these optimized parameters were validated through experiments, which showed as follows: the average qualified seed sowing rate was 91.0% (the average seed sowing space was 0.917 s). The average seed missing rate was 4.5%. The average seed blocking rate was 0.5%. The seed sowing uniformity was improved significantly. What mentioned above laid the theoretical research foundation of deeply further development of pre-seed-cutting sugarcane planters. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 21
Main heading: Seed
Controlled terms: Elasticity? - ?Flow control? - ?Plates (structural components)? - ?Velocity
Uncontrolled terms: Elastic structures? - ?Experiment research? - ?Narrow row spacing? - ?Optimized parameter? - ?Rotation velocity? - ?Test platforms? - ?Theoretical research? - ?Virtual experiments
Classification code: 408.2 Structural Members and Shapes? - ?631.1 Fluid Flow, General? - ?821.4 Agricultural Products
Numerical data indexing: Percentage 4.50e+00%, Percentage 5.00e-01%, Percentage 9.10e+01%, Percentage 9.51e+01%, Rotational_Speed 6.00e+00RPM, Time 9.17e-01s
DOI: 10.6041/j.issn.1000-1298.2020.04.013
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
42. Effect of Wood Vinegar on Physicochemical Properties and Seeding Capability of Cow Manure Aerobic Composting
Accession number: 20202008644184
Title of translation:
Authors: Xu, Chao (1, 2); Yuan, Qiaoxia (1, 2); Qin, Cuina (1, 2); Xie, Guangrong (1, 2); He, Tao (3); Song, Na (4)
Author affiliation: (1) College of Engineering, Huazhong Agricultural University, Wuhan; 430070, China; (2) Key Laboratory of Agricultural Equipment in Mid-lower Yangtze River, Ministry of Agriculture and Rural Affairs, Wuhan; 430070, China; (3) Wuhan Optics Valley Bluefire New Energy Co., Ltd., Wuhan; 430072, China; (4) Hubei Haitu Horticultural Landscape Engineering Co., Ltd., Wuhan; 430070, China
Corresponding author: Yuan, Qiaoxia(qxyuan@mail.hzau.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 353-360
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Traditional aerobic composting of cow manure is not conducive to seedling raising, and adding conditioner is an important method to improve its capability of nursery. As a by-product of agricultural and forestry waste pyrolysis industry, wood vinegar was not been effectively used. In order to optimize the pretreatment process of cow manure aerobic compost for seedling substrate, cow dung and wheat straw were used as raw materials and wood vinegar as regulator, and adding 0, 1%, 3% and 5% of wood vinegar to the compost and putting the material into the small test reactor for fermentation. Based on the analysis of the composition of wood vinegar, its effect on the aerobic composting process was studied, and then the compost material was used for seedling test. The results showed that with the increase of the concentration, the content of water, TN, TP, K+ and organic matter degradation rate showed an upward trend, however, the pH value and EC value showed a downward trend. The relative degradation rates of cellulose and hemicellulose can be enhanced by low concentration (1%) of wood vinegar. Cucumber was selected as the test crop, and the compost material was used as substrates for germination and seedling test. The germination index of the composting extracts of all groups were more than 50%, which basically reached the non-toxic requirement of plants. The highest germination index group was 1% wood vinegar group, which was 79.17%, and in the subsequent nursery test, the seedling index (0.044 9 g) of the 1% wood vinegar treatment group was significantly higher than that of the other groups (P ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 29
Main heading: Wood
Controlled terms: Acetic acid? - ?Agricultural robots? - ?Cellulose? - ?Composting? - ?Cultivation? - ?Degradation? - ?Fertilizers? - ?Manures? - ?Physicochemical properties? - ?Substrates ? - ?Testing? - ?Waste treatment
Uncontrolled terms: Aerobic composting? - ?Cellulose and hemicellulose? - ?Compost materials? - ?Degradation rate? - ?Germination index? - ?Low concentrations? - ?Organic matter degradations? - ?Pretreatment process
Classification code: 452.4 Industrial Wastes Treatment and Disposal? - ?802.2 Chemical Reactions? - ?804 Chemical Products Generally? - ?804.1 Organic Compounds? - ?811.2 Wood and Wood Products? - ?811.3 Cellulose, Lignin and Derivatives? - ?821.3 Agricultural Methods? - ?821.5 Agricultural Wastes
Numerical data indexing: Percentage 1.00e+00%, Percentage 3.00e+00%, Percentage 5.00e+00%, Percentage 5.00e+01%, Percentage 7.92e+01%
DOI: 10.6041/j.issn.1000-1298.2020.04.040
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
43. Comprehensive Effect of Rice Harvesting Straw Treatment Methods in Northeast Rice Region
Accession number: 20202008644287
Title of translation:
Authors: Sun, Ni’na (1); Dong, Wenjun (2); Wang, Xiaoyan (1); Li, Hongwen (1); Meng, Ying (2); Wei, Zhongcai (1)
Author affiliation: (1) College of Engineering, China Agricultural University, Beijing; 100083, China; (2) Institute of Crop Cultivation and Tillage, Heilongjiang Academy of Agricultural Sciences, Harbin; 150086, China
Corresponding author: Wang, Xiaoyan(xywang@cau.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 69-77
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: In order to clarify the effects of straw treatment on the quality of straw returning, tillage preparation, rice growth and yield in Northeast rice region, and conduct a comprehensive evaluation of the benefits, three straw treatment methods were set according to the agronomic requirements of straw returning and different straw treatment equipments. Specifically, three methods were as follows: chopping and spreading at harvesting (CK, combine harvester with chopper cum spreader device), straw treatment 1 after harvesting (T1, combine harvester with chopper cum spreader device + secondary spread), straw treatment 2 after harvesting (T2, combine harvester without chopper cum spreader device + chopping and spreading after harvesting). The experiment monitored the effects of different straw treatment methods on the quality of straw chopping and spreading, the quality of land preparation, the growth of rice and the yield. The experiments showed that all three straw treatment methods could achieve full amount straw returning, which could ensure normal field machinery operation and rice growth. Among them, T2 had the best comprehensive effect, which could achieve better straw chopping and spreading effect, straw burying effect, higher aboveground biomass and yield of rice. In terms of straw chopping and spreading quality, compared with CK and T1, T2 had significant differences in average straw chopping length, qualified rate of straw chopping length, and residue height. Although the unevenness of straw spreading was higher than that of T1, there was no significant difference. In terms of land preparation quality in the subsequent period, compared with CK, the vegetation coverage of T2 below the surface and below 8 cm was significantly different, which was better than CK. Compared with T1, there was a significant difference in vegetation coverage below the surface, while there was no significant difference in vegetation coverage below 8 cm. In terms of rice growth and yield, the yield of T1 and T2 treatment was 1.5% and 4.4% higher than that of CK, respectively, and the difference of T2 treatment reached a significant level. This study provided a theoretical basis for the selection of rice straw harvesting treatment methods and supporting equipment in Northeast rice region. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 34
Main heading: Harvesting
Controlled terms: Choppers (circuits)? - ?Harvesters? - ?Spreaders? - ?Vegetation
Uncontrolled terms: Above ground biomass? - ?Combine harvesters? - ?Comprehensive effect? - ?Comprehensive evaluation? - ?Field machinery? - ?Spreading effects? - ?Treatment methods? - ?Vegetation coverage
Classification code: 821.1 Agricultural Machinery and Equipment? - ?821.3 Agricultural Methods
Numerical data indexing: Percentage 1.50e+00%, Percentage 4.40e+00%, Size 8.00e-02m
DOI: 10.6041/j.issn.1000-1298.2020.04.008
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
44. Design and Experiment of Differential Pump Driven by Non-circular Gear with Free Pitch Curve
Accession number: 20202008644191
Title of translation:
Authors: Xu, Gaohuan (1); Xie, Rongsheng (1); Sun, Peifeng (1); Zhao, Huacheng (1)
Author affiliation: (1) School of Mechanical and Automotive Engineering, Zhejiang University of Water Resources and Electric Power, Hangzhou; 310018, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 411-417
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: In order to further improve the performance of differential pump, a four blade differential pump driven by non-circular gear with free pitch curve was proposed. The performance calculation model of differential pump driven by non-circular gear with free pitch curve was established. The performance analysis software of differential pump was compiled to analyze the performance of differential pump under different control points, such as displacement, flow and pulsation rate. The results showed that the free pitch curve was better than the optimal Fourier curve. The pitch curve had better local optimization ability, which can effectively improve the maximum modulus of non-circular gear without undercutting and the displacement, reduce the pulsation rate of differential pump, and improve the comprehensive performance of differential pump. Through experimental research, under the same pump size and pipeline environment, the displacement of the differential pump driven by non-circular gear with free pitch curve was increased by 6.6% compared with the optimal Fourier non-circular gear, and the maximum module without undercutting was increased by 18.7%. The bearing capacity of the non-circular gear was effectively improved, and the pulsation rate of the single pump of the differential pump was reduced by 8.3%. It can be seen that the free pitch curve non-circular gear was more conducive to improving the performance of the differential pump. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 25
Main heading: Pumps
Controlled terms: Curve fitting
Uncontrolled terms: Comprehensive performance? - ?Differential pumps? - ?Experimental research? - ?Local optimizations? - ?Maximum modules? - ?Non-circular gears? - ?Performance analysis? - ?Performance calculation
Classification code: 618.2 Pumps? - ?921.6 Numerical Methods
Numerical data indexing: Percentage 1.87e+01%, Percentage 6.60e+00%, Percentage 8.30e+00%
DOI: 10.6041/j.issn.1000-1298.2020.04.048
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
45. Automatic Recognition Method of Dairy Cow Estrus Behavior Based on Machine Vision
Accession number: 20202008644223
Title of translation:
Authors: Wang, Shaohua (1, 2); He, Dongjian (1, 2); Liu, Dong (1, 2)
Author affiliation: (1) College of Mechanical and Electronic Engineering, Northwest A&F University, Yangling; Shaanxi; 712100, China; (2) Key Laboratory of Agricultural Internet of Things, Ministry of Agriculture and Rural Affairs, Yangling; Shaanxi; 712100, China
Corresponding author: He, Dongjian(hdj168@nwsuaf.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 241-249
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Milk is one of the main sources for humans to obtain protein, and dairy industry is also an important pillar industry for agricultural personnel in China to increase their income. Detecting the estrus of dairy cows in time, artfical insemination them at the right time, and reducing cows’ emptiness are the key means to increase the milk production of dairy farms. As the methods of identifying dairy cow estrus based on physical signs such as activity or body temperature often cause stress reactions of cows and accuracy is also not high enough, a non-contacted automatic method for recognizing estrus behaviors of cows was proposed. In this method, an improved Gaussian mixture model to achieve target detection for moving cows was used. Then, interference images were removed based on the information of color and texture. Next, a cow behavior classification network model based on AlexNet was trained to identify cows’ mounting behavior. Finally, based on the classification model result, automatic recognition of estrus behavior of cows was realized. Experiments on the test video data sets showed that the accuracy rate of the method was 100%, and the recall rate was 88.24%. The method can be used for daily estrus monitoring of dairy farms, and it can also provide support for decision-making of their production management. The research can also serve as a reference for the automatic recognition of other large animals’ behaviors. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 36
Main heading: Behavioral research
Controlled terms: Agricultural robots? - ?Computer vision? - ?Dairies? - ?Decision making? - ?Farms? - ?Gaussian distribution? - ?Object recognition? - ?Textures
Uncontrolled terms: Automatic method? - ?Automatic recognition? - ?Automatic recognition method? - ?Classification models? - ?Color and textures? - ?Gaussian Mixture Model? - ?Interference images? - ?Production management
Classification code: 723.5 Computer Applications? - ?821 Agricultural Equipment and Methods; Vegetation and Pest Control? - ?822.1 Food Products Plants and Equipment? - ?912.2 Management? - ?922.1 Probability Theory? - ?971 Social Sciences
Numerical data indexing: Percentage 1.00e+02%, Percentage 8.82e+01%
DOI: 10.6041/j.issn.1000-1298.2020.04.028
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
46. Effect of Hub Clearance on Hydraulic Performance in Bidirectional Axial-flow Pump
Accession number: 20202008644259
Title of translation:
Authors: Meng, Fan (1); Li, Yanjun (1); Yuan, Shouqi (1); Yuan, Jianping (1); Zheng, Yunhao (1); Yang, Pinghui (2)
Author affiliation: (1) Research Center of Fluid Machinery Engineering and Technology, Jiangsu University, Zhenjiang; 212013, China; (2) Wuhan Special Industrial Pump Factory Co., Ltd., Wuhan; 430058, China
Corresponding author: Li, Yanjun(lyj782900@ujs.edu.cn)
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 131-138
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Variable angle adjustment is an effective measure which is usually used to widen the operating range of axial-flow pump. In order to ensure the adjustability of blade placement angle in bidirectional axial-flow pump, a certain clearance will be reserved between blade and hub during structure design of the impeller. The hub clearance will change with the adjustment of the blade installation angle. According to engineering experience, inappropriate size of the hub clearance will significantly affect the hydraulic performance of the axial flow pump. Therefore, the effects of hub clearance on hydraulic performance of bidirectional axial-flow pump should be analyzed. Five clearance radii of impeller hub (0 mm, 1 mm, 3 mm, 5 mm and 8 mm) were designed. Three-dimensional Reynolds-averaged Navier-Stokes equations was solved by CFX to predict external characteristics of bidirectional axial-flow pump. The results were verified by experimental data. It was shown that when hub clearance was too large, head and torque of pump were decreased significantly both under forward and reverse condition. The decline of pump efficiency due to increase of hub clearance under large flowrate was more obvious. And the maximum relative decline ratios of pump efficiency under forward and reverse condition were 5.72 percentage points and 3.48 percentage points respectively. In impeller passage, the leakage rate of hub clearance was increased with the increase of clearance radius. Near impeller hub, the axial velocity and circulation of impeller outlet declined remarkable with the increase of clearance radius. This result can provide useful suggestion to structural design of bidirectional axial-flow pump. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 26
Main heading: Navier Stokes equations
Controlled terms: Axial flow? - ?Efficiency? - ?Impellers? - ?Pumps? - ?Structural design
Uncontrolled terms: Effective measures? - ?External characteristic? - ?Hydraulic performance? - ?Impeller passage? - ?Installation angle? - ?Percentage points? - ?Placement angles? - ?Reynolds Averaged Navier-Stokes Equations
Classification code: 408.1 Structural Design, General? - ?601.2 Machine Components? - ?618.2 Pumps? - ?631.1 Fluid Flow, General? - ?913.1 Production Engineering? - ?921.2 Calculus
Numerical data indexing: Size 0.00e+00m, Size 1.00e-03m, Size 3.00e-03m, Size 5.00e-03m, Size 8.00e-03m
DOI: 10.6041/j.issn.1000-1298.2020.04.015
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
47. Application of PID Control Based on SOA Optimization in Intelligent Irrigation System
Accession number: 20202008643861
Title of translation: SOAPID
Authors: Xu, Jinghui (1, 2); Wang, Lei (2); Tan, Xiaoqiang (2); Wang, Yichen (3); Zhao, Zhongsheng (2); Shao, Mingye (3)
Author affiliation: (1) Key Laboratory of Agricultural Soil and Water Engineering in Arid and Semiarid Areas, Ministry of Education, Northwest A&F University, Yangling; Shaanxi; 712100, China; (2) College of Water Resources and Architectural Engineering, Northwest A&F University, Yangling; Shaanxi; 712100, China; (3) College of Mechanical and Electronic Engineering, Northwest A&F University, Yangling; Shaanxi; 712100, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 261-267
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: The control of water pump water supply is an important part of the intelligent irrigation control system. The water supply in the water supply process is beneficial to the development of crop roots and the absorption of minerals in the soil within the optimal control range. In the intelligent irrigation control, due to the nonlinear, time-varying and hysteresis problems of the pump control, the traditional proportion integration differentiation (PID) control is difficult to achieve good control effects. In order to solve the instability problem of pump control in intelligent irrigation system, based on the traditional PID control algorithm, the seeker optimization algorithm (SOA) was used to optimize PID control. The results showed that the optimal control algorithm can effectively solve the problems of nonlinearity, time-varying and hysteresis in the control of intelligent irrigation pumps. In order to verify the actual effect of SOA optimization PID control, it was compared with particle swarm optimization (PSO) optimized PID control and genetic algorithms (GA) optimized PID control. The experimental simulation results showed that the PID control based on SOA optimization had the shortest response time, smallest overshoot, and no oscillation in the steady state process. Therefore, it was suitable for pump control in intelligent irrigation systems. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 27
Main heading: Time varying control systems
Controlled terms: Genetic algorithms? - ?Hysteresis? - ?Intelligent control? - ?Irrigation? - ?Particle swarm optimization (PSO)? - ?Three term control systems? - ?Water absorption? - ?Water supply
Uncontrolled terms: Experimental simulations? - ?Instability problems? - ?Intelligent irrigation systems? - ?Intelligent irrigations? - ?Optimal control algorithm? - ?Proportion integration differentiation control(PID)? - ?Seeker optimization algorithm? - ?Steady state process
Classification code: 446.1 Water Supply Systems? - ?723 Computer Software, Data Handling and Applications? - ?731.1 Control Systems? - ?802.3 Chemical Operations? - ?821.3 Agricultural Methods? - ?961 Systems Science
DOI: 10.6041/j.issn.1000-1298.2020.04.030
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
48. Method of Getting Complete Surface Information of Citrus by Inspection Robot
Accession number: 20202008644212
Title of translation:
Authors: Wang, Yi (1); He, Yu (1); Wang, Kai (1); Xiong, Longye (1); Wang, Zhuo (1); Zhang, Yitan (1)
Author affiliation: (1) College of Mechanical Engineering, Chongqing University of Technology, Chongqing; 400054, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 232-240
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: In order to monitor the growth of citrus, a method to obtain the complete surface information of single citrus fruit by inspection robot was proposed. LabelMe was used as a tool to mark citrus fruits and segmented branches and trunks, and the model of Mask R-CNN was used to train and recognize them. The 3D information of citrus fruits and segmented branches and trunks can be extracted from the images with depth information taken by Kinect V2 camera. According to the growth of citrus fruit and the occurrence of diseases and insect pests, the surface of citrus fruit was divided into regions, and integrated system was used to describe the information acquisition rate. The CCD camera connected to the end of the manipulator was used to acquire the surface information of the citrus fruit. Three positions of the manipulator were proposed to obtain the complete surface information of the citrus fruit. A prototype inspection robot was built and simulated under the robot operating system (ROS). The process of citrus surface information acquisition in the laboratory environment was proposed. In the laboratory environment, the complete surface information of citrus was obtained by the inspection robot. The experimental results showed that the closer the ratio of horizontal to vertical stems of citrus fruit was to 1, the more complete the outer surface information obtained by photographing was. When the photographing mode of three photographing positions was used, the higher the success rate and work efficiency of avoiding obstacles can be ensured while the citrus surface integrity rate was obtained. The citrus surface information acquisition rate can reach 94.21%, and the average movement time of the manipulator was 86.57 s. The research result provided a method for human to get the surface condition of citrus, monitor the growth of citrus and control the diseases and insect pests. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 25
Main heading: Citrus fruits
Controlled terms: CCD cameras? - ?Disease control? - ?Inspection? - ?Manipulators? - ?Robots
Uncontrolled terms: Information acquisitions? - ?Inspection robots? - ?Integrated systems? - ?Laboratory environment? - ?Robot operating systems (ROS)? - ?Surface conditions? - ?Surface information? - ?Surface integrity
Classification code: 714.2 Semiconductor Devices and Integrated Circuits? - ?731.5 Robotics? - ?821.4 Agricultural Products
Numerical data indexing: Percentage 9.42e+01%, Time 8.66e+01s
DOI: 10.6041/j.issn.1000-1298.2020.04.027
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
49. Individual Identification of Dairy Cows Based on Improved YOLO v3
Accession number: 20202008644210
Title of translation: YOLO v3
Authors: He, Dongjian (1, 2); Liu, Jianmin (1, 2); Xiong, Hongting (1, 3); Lu, Zhongzhong (1, 2)
Author affiliation: (1) College of Mechanical and Electronic Engineering, Northwest A&F University, Yangling; Shaanxi; 712100, China; (2) Key Laboratory of Agricultural Internet of Things, Ministry of Agriculture and Rural Affairs, Yangling; Shaanxi; 712100, China; (3) Shaanxi Key Laboratory of Agricultural Information Perception and Intelligent Service, Yangling; Shaanxi; 712100, China
Source title: Nongye Jixie Xuebao/Transactions of the Chinese Society for Agricultural Machinery
Abbreviated source title: Nongye Jixie Xuebao
Volume: 51
Issue: 4
Issue date: April 25, 2020
Publication year: 2020
Pages: 250-260
Language: Chinese
ISSN: 10001298
CODEN: NUYCA3
Document type: Journal article (JA)
Publisher: Chinese Society of Agricultural Machinery
Abstract: Aiming to achieve an effective identification of dairy cows in a non-contact and high-precision environment of farming, a method to identify dairy cows based on the improved YOLO v3 deep convolutional neural network was proposed. According to this method, multiple cameras were installed above the passageway between the doors of the milking room. The back of cows was videotaped automatically and regularly, after which the image of the cow’s back was captured by applying video frame decomposition technology. Upon the removal of images noise with bilateral filters and the enhancement of brightness and contrast with the pixel linear transformation method, the individual dairy cows were serial numbered manually. For the cows to be better identified in complex environments, the YOLO v3 recognition model that features optimized anchor boxes and improved network structure was constructed by making reference to the Gaussian YOLO v3 algorithm. From totally 36 790 images showing the back of 89 cows, 22 074 were randomly selected as the training set, while the remaining ones were classified into either the validation set or the test set. The results showed that the accuracy of the improved YOLO v3 was 95.91%, the recall rate was 95.32%, the mAP was 95.16%, the IoU was 85.28%, the actual frame rate of detection was 32 f/s, and the accuracy rate of identification was 0.94 percentage points higher compared with that of the YOLO v3 and 1.90 percentage points higher than that of Faster R-CNN. Moreover, the detection speed was eight times faster than that of Faster R-CNN, while the F1 value of dairy cows with pure black back was 2.75 percentage points higher compared with that of the original algorithm. The method showed such advantages as low cost and excellent performance, which were not only conducive to the real-time identification of dairy cows in complex farm environments, but also to the extended application of this method to the identification of other large-sized animals. ? 2020, Chinese Society of Agricultural Machinery. All right reserved.
Number of references: 34
Main heading: Image enhancement
Controlled terms: Complex networks? - ?Convolutional neural networks? - ?Deep neural networks? - ?Linear transformations? - ?Video recording
Uncontrolled terms: Complex environments? - ?Individual identification? - ?Linear transformation method? - ?Network structures? - ?Original algorithms? - ?Percentage points? - ?Real-time identification? - ?Recognition models
Classification code: 716.4 Television Systems and Equipment? - ?722 Computer Systems and Equipment? - ?921.3 Mathematical Transformations
Numerical data indexing: Percentage 8.53e+01%, Percentage 9.52e+01%, Percentage 9.53e+01%, Percentage 9.59e+01%
DOI: 10.6041/j.issn.1000-1298.2020.04.029
Compendex references: YES
Database: Compendex
Compilation and indexing terms, Copyright 2020 Elsevier Inc.
Data Provider: Engineering Village
您是本站第 访问者
通信地址:北京德胜门外北沙滩1号6信箱
邮编:100083 传真:64867367
电话:64882610 E-mail:njxb@caams.org.cn
技术支持:北京勤云科技发展有限公司
版权所有:农业机械学报 ® 2024 版权所有