尹建军,高强,陈亚明.基于刚柔接触动力学的打结器虚拟打结方法研究[J].农业机械学报,2016,47(9):85-92.
Yin Jianjun,Gao Qiang,Chen Yaming.Virtual Knotting Method of Knotter Based on Rigid-flexible Contact Dynamics[J].Transactions of the Chinese Society for Agricultural Machinery,2016,47(9):85-92.
摘要点击次数: 859
全文下载次数: 456
基于刚柔接触动力学的打结器虚拟打结方法研究   [下载全文]
Virtual Knotting Method of Knotter Based on Rigid-flexible Contact Dynamics   [Download Pdf][in English]
投稿时间:2016-02-19  
DOI:10.6041/j.issn.1000-1298.2016.09.013
中文关键词:  打捆机  打结器  接触动力学  虚拟打结  ADAMS
基金项目:国家自然科学基金项目(51375215)、镇江市重点研发计划项目(NY2015009)和江苏高校优势学科建设工程项目(苏政办发(2014)37号)
作者单位
尹建军 江苏大学 
高强 江苏大学 
陈亚明 江苏大学 
中文摘要:针对打结器结构改进或参数调整后在设计阶段难以评判优劣而增加制造投入成本的问题,以打结器能否打出绳结为评判准则,提出了一种基于刚柔接触动力学的打结器虚拟打结方法。该方法利用ADAMS的Bushing连接建立大变形柔性捆绳的动力学模型,通过对捆绳和刚性构件之间设置多接触约束和载荷施加,实现了完整的打结器虚拟打结仿真过程,研究了捆绳在拉力作用下成结的刚柔交互力学行为。通过对打结器样机的成结动作与虚拟打结的仿真结果进行对比分析,验证了捆绳动力学模型与刚柔接触动力学仿真模型的正确性,可作为评价设计优劣、保证打结器一次性制造成功的有效方法。利用该虚拟打结方法分析了打结嘴与夹绳盘动作时序差φ对打结器成结的影响,对判定打结器参数匹配后能否成结或成结优劣起到了直观验证作用。
Yin Jianjun  Gao Qiang  Chen Yaming
Jiangsu University,Jiangsu University and Jiangsu University
Key Words:baler  knotter  contact dynamics  virtual knotting  ADAMS
Abstract:Aiming at the problem of increasing investment cost of knotter production due to difficulty in evaluation of good or bad design after structure improvement or parameters adjustment of the knotter, a kind of virtual knotting method of knotter based on rigid flexible contact dynamics was presented according to the judgment rule of whether the knotter could tie a knot during design phase. The method used the Bushing connection tool under ADAMS to build up dynamic model of flexible rope with large deformation. A complete virtual knotting simulation process of the knotter was implemented by setting up multiple contact constraint between the rope and rigid component of the knotter and applying load to the rope. Rigid flexible interactive mechanical behaviors of tying a knot of the knotter were studied under the action of pulling force of the rope. The comparison analyses between knotting movements of the knotter prototype and virtual knotting results validated the correctness of dynamic model of the rope and simulation model of rigid flexible contact dynamics. It may be regarded as an effective method to evaluate good or bad design and guarantee disposable successful production of the knotter. The effects of the timing sequence difference value φ between the motion of knotting hook and the motion of rope holding plate on knotting motion of the knotter were analyzed by using the proposed virtual knotting method, which can play visual validation role to judge whether the knotter can knot or tie a good and bad knot after parameters match of the knotter.

Transactions of the Chinese Society for Agriculture Machinery (CSAM), in charged of China Association for Science and Technology (CAST), sponsored by CSAM and Chinese Academy of Agricultural Mechanization Science(CAAMS), started publication in 1957. It is the earliest interdisciplinary journal in Chinese which combines agricultural and engineering. It always closely grasps the development direction of agriculture engineering disciplines and the published papers represent the highest academic level of agriculture engineering in China. Currently, nearly 8,000 papers have been already published. There are around 3,000 papers contributed to the journal each year, but only around 600 of them will be accepted. Transactions of CSAM focuses on a wide range of agricultural machinery, irrigation, electronics, robotics, agro-products engineering, biological energy, agricultural structures and environment and more. Subjects in Transactions of the CSAM have been embodied by many internationally well-known index systems, such as: EI Compendex, CA, CSA, etc.

   下载PDF阅读器