周浩,师清翔,耿令新,马萌,袁华杰,李宇航.基于免割收获的小麦扶持脱粒装置试验优化[J].农业机械学报,2013,44(Supp2):52-56,31.
Zhou Hao,Shi Qingxiang,Geng Lingxin,Ma Meng,Yuan Huajie,Li Yuhang.Experiment of Wheat Supported Threshing Apparatus Based on Free-cutting Harvest[J].Transactions of the Chinese Society for Agricultural Machinery,2013,44(Supp2):52-56,31.
摘要点击次数: 2809
全文下载次数: 1516
基于免割收获的小麦扶持脱粒装置试验优化   [下载全文]
Experiment of Wheat Supported Threshing Apparatus Based on Free-cutting Harvest   [Download Pdf][in English]
  
DOI:10.6041/j.issn.1000-1298.2013.S2.011
中文关键词:  小麦 免割收获 扶持 脱粒装置
基金项目:“十二五”国家科技支撑计划资助项目(2011BAD20B10)
作者单位
周浩 河南科技大学车辆与动力工程学院 
师清翔 河南科技大学车辆与动力工程学院 
耿令新 河南科技大学车辆与动力工程学院 
马萌 河南科技大学车辆与动力工程学院 
袁华杰 河南科技大学车辆与动力工程学院 
李宇航 河南科技大学车辆与动力工程学院 
中文摘要:利用小麦扶持脱粒装置试验台,以脱粒损失率为指标进行了滚筒转速、板齿倾角单因素试验,初步确定了脱粒滚筒转速和板齿倾角。在此基础上,以脱粒损失率和含杂率为指标,进行了滚筒转速、筛孔尺寸和脱粒间隙三因素正交试验和滚筒转速、脱粒间隙两因素回归试验,优化确定了该扶持脱粒装置的最佳参数组合。当筛孔尺寸为14 mm、板齿倾角为0°、脱粒间隙为18.5 mm、滚筒转速为927 r/min、滚筒长度为700 mm时,脱粒损失率和含杂率分别为2.71%和19.20%。
Zhou Hao  Shi Qingxiang  Geng Lingxin  Ma Meng  Yuan Huajie  Li Yuhang
Vehicle and Motive Power Engineering College, Henan University of Science and Technology;Vehicle and Motive Power Engineering College, Henan University of Science and Technology;Vehicle and Motive Power Engineering College, Henan University of Science and Technology;Vehicle and Motive Power Engineering College, Henan University of Science and Technology;Vehicle and Motive Power Engineering College, Henan University of Science and Technology;Vehicle and Motive Power Engineering College, Henan University of Science and Technology
Key Words:Wheat Free-cutting harvest Supported Threshing apparatus
Abstract:By using the self-designed threshing apparatus test- bed, single- factor tests of roller- speed and tooth- angle were carried out and the values of these two factors were obtained. On this basis, the three factors orthogonal test, including the speed of the roller, the mesh aperture and the thresh gap, was researched. The two factors regression experiment, including the roller speed and the thresh gap, was also studied. Optimum parameter combination of threshing apparatus was obtained. When the mesh aperture was 14 mm, tooth angle was 0°, thresh gap was 18.5 mm, roller speed was 927 r/min and roller length was 700 mm, the threshing loss rate was 2.71% and the trash content was 19.20%.

Transactions of the Chinese Society for Agriculture Machinery (CSAM), in charged of China Association for Science and Technology (CAST), sponsored by CSAM and Chinese Academy of Agricultural Mechanization Science(CAAMS), started publication in 1957. It is the earliest interdisciplinary journal in Chinese which combines agricultural and engineering. It always closely grasps the development direction of agriculture engineering disciplines and the published papers represent the highest academic level of agriculture engineering in China. Currently, nearly 8,000 papers have been already published. There are around 3,000 papers contributed to the journal each year, but only around 600 of them will be accepted. Transactions of CSAM focuses on a wide range of agricultural machinery, irrigation, electronics, robotics, agro-products engineering, biological energy, agricultural structures and environment and more. Subjects in Transactions of the CSAM have been embodied by many internationally well-known index systems, such as: EI Compendex, CA, CSA, etc.

   下载PDF阅读器